Silvercrest STG 70 B3 - Manual (Page 10)

8 GB
17. Insert the plastic sleeve
(bearing) into the door.
18. Insert the upper hinge into
the plastic sleeve (bear-
ing). In the process, pay
attention to the small plas-
tic ring.
19. Fasten the upper hinge
with the three screws.
20. Check whether the door can be opened and closed and
whether it is secured straight. Check whether the door
seal 10 is in air-tight contact all the way round. If neces-
sary, correct the fit of the lower hinge (step 14.).
21. Pull out the small plastic part (on the underside of the
cover plate) on one side and insert it again on the other
side.
22. Push the cover plate into position from the front. In the
process, make sure that the semicircular cut-outs under
the cover plate engage exactly into the two round brack-
ets on the front edge of the appliance. Check that the
cover plate is fitted securely by testing whether it is possi-
ble to pull the front page upwards. If so, repeat this step.
23. Fasten the cover plate to the rear panel with the two
screws.
24. Position the appliance in its proper place, align it horizon-
tally using the feet and finally check that the door is
straight.
11. Troubleshooting
If your device fails to function as required, please try this
checklist first. Perhaps there is only a minor problem and you
can solve it yourself.
DANGER! Do not attempt to repair the appliance
yourself under any circumstances.
Fault Possible causes/Action
No function
• Is the appliance being supplied with
power?
• Is the appliance switched on?
Unusual noises
• Gentle noises caused by the motor
and the flow of refrigerant in the lines
are quite normal.
• Check whether the appliance is posi-
tioned firmly and horizontally. If neces-
sary, align the appliance with the
height-adjustable feet 12.
• Is the appliance touching other objects
or the wall?
A layer of ice
forms quickly in
the appliance.
• Was the door left open for a long time
or frequently during operation?
• Check whether the door seal is clean
and is in air-tight contact all the way
round.
• Check whether the appliance is posi-
tioned firmly and horizontally. If neces-
sary, align the appliance with the
height-adjustable feet 12.
The tempera-
ture in the appli-
ance is too high.
• Has the door been left open?
• Have you frozen fresh foods in the last
24 hours? Was the quantity too large?
Were the foods too warm? If not al-
ready done, press the ALARM/SU-
PER button 4 briefly. The SUPER
LED 5 lights up.
• Check the setting of the temperature
controller SET 1. If necessary, select a
higher temperature level.
• Check the installation location: Is there
an oven, another cooling device or a
different heat source nearby? Is the
ambient temperature too high?
• Check the clearances around the ap-
pliance. Can the air circulate ade-
quately around the appliance?
It is difficult to
open the door.
• This is normally if you have already
opened the door shortly beforehand. A
vacuum is formed in the appliance due
to the cooling of the air, which is com-
pensated for again within a few min-
utes.
The device
bleeps.
• Either the door alarm or the tempera-
ture alarm is active. Close the door; or
– to reduce the temperature more rap-
idly – activate the Superfrost function.
Door cannot be
closed. • Check whether all the drawers are in
their correct position.
The refrigerant
circuit has been
damaged.
• Ventilate the room thoroughly, discon-
nect the power plug and keep all
sources of ignition and naked flames
at a distance without fail.
Please con-
sult the Service Centre.
The door seal is
deformed or
damaged. • Please consult the Service Centre.
__RP71979_B6.book Seite 8 Freitag, 23. März 2012 2:21 14