Fulton Performance 1413230134 - Manual (Page 2)

Limited Lifetime Warranty (“Warranty”). Cequent Trailer Products, Inc. ("We" or “Us”) warrants to the original consumer purchaser only ("You") that the product will
be free from material defects in both material and workmanship, ordinary wear and tear excepted; provided that installation and use of the product is in accordance with
product instructions. There are no other warranties, express or implied, including the warranty of merchantability or fitness for a particular purpose. This warranty is
not transferable.
Limitations on the Warranty. This Warranty does not cover: (a) normal wear and tear; (b) damage through abuse, neglect, misuse, or as a result of any accident or in any
other manner; (c) damage from misapplication, overloading, or improper installation; (d) improper maintenance and repair; and (e) product alteration in any manner by
anyone other than Us, with the sole exception of alterations made pursuant to product instructions and in a workmanlike manner.
Obligations of Purchaser. To make a Warranty claim, contact Us at 1050 Indianhead Drive, Mosinee, WI 54455, 1-800-604-9466, identify the product by model number,
and follow the claim instructions that will be provided. Any returned product that is replaced by Us becomes our property. You will be responsible for return shipping
costs. Please retain your purchase receipt to verify date of purchase and that You are the original consumer purchaser. The product and the purchase receipt must be
provided to Us in order to process Your Warranty claim.
Remedy Limits. Product replacement is Your sole remedy under this Warranty. We shall not be liable for service or labor charges incurred in removing or replacing a
product or any incidental or consequential damages of any kind.
Assumption of Risk. You acknowledge and agree that any use of the product for any purpose other than the specified use(s) stated in the product instructions is at Your own
risk.
Governing Law. This Warranty gives You specific legal rights, and You also may have other rights which vary from state to state. This Warranty is governed by the laws
of the State of Michigan, without regard to rules pertaining to conflicts of law. The state courts located in Oakland County, Michigan shall have exclusive jurisdiction
for any disputes relating to this Warranty.
47912 Haylyard Dr. Suite 100
Plymouth, MI 48170 USA
800/632-3290
www.cequentgroup.com
Maintenance
Installation Instructions (Cont.)
Limited Lifetime Warranty
The F2 jack is designed with precision fit components and corrosion resistant materials to minimize the frequency of maintenance. Occasional cleaning
with mild soap and water along with light oil lubrication of pivot points will prolong peak performance and appearance.
Lock
Nut
Roller
Spacer
Washer
Bolt
Handle
Bolt-on:
Available in 3”x 3”, 3”x 4”, or 3”x5” trailer tubes
only. Position swivel bracket and U-bolts to allow
proper mounting to trailer. Tighten nuts and torque to
20-25 ft-lbs.
Nut
Lock Washer
U-Bolt
(4” shown)
Bolt-on
(U-bolts)
Optional
Wheel Wedge
To lock
Optional
Handle Hold-Up
To disengage
Footplate
Adjusting Swivel Mount Height (If Necessary):
With jack removed from trailer, loosen the two swivel fasteners until
the slide block moves freely along outer tube. To access the upper
bolt be sure the swivel bracket is rotated in the horizontal (3”
mounting) position as shown. Adjust swivel mount to desired
location and re-torque to 60-70 ft.-lbs. After adjustment, check for
proper swivel and pin engagement.
Swivel Fasteners
Handle Assembly
Optional Wheel Wedge:
Assemble the optional Wheel Wedge
as shown in the diagram below and
torque to 6-9 in-lbs. To activate, press
downward until wedge locks into
place. To release, lift up until pressure
is released from wheels. Wheel Wedge
is not intended to be a wheel brake or
stop. Footplate: Thread footplate into the bottom of the
jack tube. Torque to 60-70 ft.-lbs.
Optional Handle Hold-Up:
To assemble, place Handle Hold-up with its
stop block pointing toward top of jack. Center
hold-up on handle and drive pin flush through
hold-up & both tabs. Proper assembly allows
Handle Hold-up to rotate down in the event of
crank handle bypass.
Jack and handle shown
in stowed position
Installing Handle Assembly:
Assemble handle assembly as shown and
torque locknut to 20-25 in-lbs.
We declare under our sole responsibility that the F2 Trailer Jack is in conformity with
EN-12100-2:2003 Safety Machinery; Machinery Directive 98/37/EC.