Eltax AVR-900 - Manual (Page 16)

16
BASIC OPERATION
BASIC OPERATION 1
1. Press the POWER button to ON.
2. Press STANDBY button to switch on the unit.
3.Select the desired source by rotating the INPUT
SELECTOR knob.
DVD (ANA, OPT, COAX)
TUNER (FREQUENCY)
TAPE
AUX
VIDEO 1 (ANA, OPT,)
VIDEO 2 (ANA, OPT,)
VIDEO 3(ANA)
Note: DIGITAL IN is used to select one of the 3
Modes.
ANA→OPT→COAX
When DVD, VIDEO 1, VIDEO 2 is selected, press the
DIGITAL IN button and select “ANALOG”, “OPTICAL”
or “COAXIAL” in accordance with your connection.
If
appears on the display:
A digital input source (OPT or COAX) has been
selected, and the source is connected successfully.
If “ UNLOCK” appeared for 5 seconds on the display:
The source is not connected properly or the source is
not switched on.
In that case, connect and switch the source on, or
select ANALOG by pressing the DIGITAL IN button.
4. Play the source, and gradually turn up the volume to
the required level with the MASTER VOLUME control.
BASIC OPERATION 2
A. POWER & STANDBY/ON button
Press this button to turn the power on.
Press it again to turn the system off (power standby
mode).
The STANDBY indicator lights up in power standby
mode and goes out when this unit is turned on.
B. DTS /DOLBY DIGITAL
With this unit in the “DTS /DOLBY DIGITAL” mode,
you can enjoy up to 5.1 channels of digital surround
sound.
C. STEREO
With the unit in the STEREO mode, only Front Left and
Front Right Speaker and Woofer have output.
D. PRO LOGIC IIx
Dolby® Pro Logic® IIx technology (PLIIx) is an
extension of Dolby Pro Logic II (PLII) matrix-decoding
technology. Dolby Pro Logic IIx technology offers
decoders more flexibility in deriving additional outputs to
take better advantage of all the amplifiers and speakers
found in higher-end surround systems, and to do so from
a wider range of program material and sources.
There are two standard modes: Movie, Music.
How to get PL II x:
After power on this unit
1. Press the PRO LOGIC IIx key on the front panel or on
the remote, you will get SURROUND BACK 1
SPEAKER DOLBY PL II x 6 MOVIE MODE (factory
default mode), press the PRO LOGIC IIx key again, you
will get SURROUND BACK 1 SPEAKER DOLBY PL II
x 6 MUSIC MODE;
2. Press the SURROUND BACK key on the front panel,
you will get SURROUND BACK 1 SPEAKER DOLBY
PL II x 6 MUSIC MODE (if the previous mode is movie
mode, you will get SURROUND BACK 1SPEAKER
DOLBY PL II x 6 MOVIE MODE), by this time, if you
press PRO LOGIC IIx key, you will get SURROUND
BACK 1SPEAKER DOLBY PL II x 6 MOVIE MODE;
3. Press the SURROUND BACK key on the front panel,
you will get SURROUND BACK OFF DOLBY PL II
MOVIE, by this time, if you press PRO LOGIC IIx key,
you will get SURROUND BACK OFF DOLBY PL II
MUSIC.
Note: During the press, the corresponding wording
appears on the display.
E. SURROUND MODE
This mode is possible to achieve a realistic sound field
with a “three dimensional” feel, giving the sense of
distance, movement and relative position, and creating a
surprisingly real and powerful sense of presence when
playing movie software in AV rooms.
There are six surround modes: THEATER, HALL,
PASSTHRU, MOVIE, MUSIC, and ROOM.
F. DIRECT IN
Press this button when you want to enjoy the 8 discrete
channels of high quality digital audio from the external
source.
G. ORIGINAL SETUP
When this unit is ON, use a paper clip to press this button
for more than 3 seconds to reset the whole system
(including memories).
H. BALANCE control
This control is used to adjust the balance of the front
speakers. Normally set to the center position.