Enterasys Networks XSR-3020 - Manual (Page 4)

ii
Regulatory Compliance Information
Federal Communications Commission (FCC) Notice
The XSR complies with Title 47, Part 15, Class A of FCC rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
NOTE: The XSR has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the XSR is operated in a
commercial environment. This XSR uses, generates, and can radiate radio frequency energy and if not installed in accordance
with the operator’s manual, may cause harmful interference to radio communications. Operation of the XSR in a residential
area is likely to cause interference in which case you will be required to correct the interference at your own expense.
WARNING: Modifications or changes made to the XSR, and not approved by Enterasys Networks may void the authority
granted by the FCC or other such agency to operate the XSR.
The XSR complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal
Attachments (ACTA). A label on the circuit board of the Network Interface Module contains, among other information, a
product identifier in the format listed in the following table. If requested, this number must be provided to the telephone
company.
A plug and jack used to connect the XSR to the premises wiring and telephone network must comply with the applicable FCC
Part 68 rules and requirements adopted by ACTA. Refer to the following table and installation instructions for details.
Codes applicable to this equipment:
If the XSR harms the telephone network, the telephone company will notify you in advance that it may need to temporarily
discontinue service. But if advance notice is not practical, the telephone company will notify you as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation
of the XSR. If this happens, the telephone company will provide advance notice for you to make necessary modifications and
maintain uninterrupted service.
If you experience trouble with the XSR, for repair or warranty information, please contact Enterasys Networks, Inc., at 978‐684‐
1000. If the XSR is causing harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is solved. The XSR is not intended to be repaired by the customer.
Product Product Identifier
NIM-T1/E1-xx, NIM-CT1E1/PRI-xx US: 5N5DENANET1
NIM-BRI-U-xx US: 5N5DENANEBU
NIM-ADSL-AC-xx US: 5N5DL02NEAA
NIM-DIRELAY-xx US: 5N5DENANEDI
NIM-TE1-xx, NIM-CTE1-PRI-xx US: 5N5DENANECT
Product Jack Used
NIM-T1/E1-xx, NIM-CT1E1/PRI-xx,
NIM-DIRELAY-xx, NIM-TE1-xx,
NIM-CTE1-PRI-xx RJ48C
NIM-BRI-U-xx RJ49C
NIM-ADSL-AC-xx RJ11C
Product Facilities Interface Code (FIC) Service Order Code (SOC)
NIM-T1/E1-xx, NIM-CT1E1/PRI-xx,
NIM-DIRELAY-xx, NIM-TE1-xx,
NIM-CTE1-PRI-xx 04DU9.BN, 04DU9.DN,
04DU9.1KN, 04DU9.1SN 6.0N
NIM-BRI-U-xx 02IS5 6.0N
NIM-ADSL-AC-xx 02LS2 7.0Y