Document Outline

• Contents
  • 1 Mounting 5
  • 2 Electrical connections 6
    • 2.1 Connecting diagram 6
    • 2.2 Terminal connection 6
  • 3 Operation 10
    • 3.1 Front view 10
    • 3.2 Behaviour after power-on 11
    • 3.3 Operating level 11
    • 3.4 Maintenance manager / Error list 12
    • 3.5 Self-tuning 14
      • 3.5.1 Preparation for self-tuning 14
      • 3.5.2 Self-tuning sequence 14
      • 3.5.3 Self-tuning start 15
      • 3.5.4 Self-tuning cancellation 15
      • 3.5.5 Acknowledgement procedures in case of unsuccessful self-tuning 16
      • 3.5.6 Examples for self-tuning attempts 16
    • 3.6 Manual tuning 17
    • 3.7 Alarm handling 18
    • 3.8 Operating structure 20
  • 4 Configuration level 21
    • 4.1 Configuration survey 21
    • 4.2 Configuration 22
    • 4.3 Set-point processing 29
    • 4.4 Configuration examples 30
      • 4.4.1 On-Off controller / Signaller (inverse) 30
      • 4.4.2 2-point controller (inverse) 31
      • 4.4.3 3-point controller (relay & relay) 32
      • 4.4.4 3-point stepping controller (relay & relay) 33
      • 4.4.5 Continuous controller (inverse) 34
      • 4.4.6 D - Y - Off controller / 2-point controller with pre-contact 35
      • 4.4.7 KS4x-1 with measured value output 36
  • 5 Parameter setting level 37
    • 5.1 Parameter survey 37
    • 5.2 37
    • 5.3 37
    • 5.4 Parameters 38
    • 5.5 Input scaling 40
      • 5.5.1 Input Inp.1 40
      • 5.5.2 Input InP.2 40
  • 6 Calibration level 41
  • 7 Programmer 44
  • 8 Timer 46
    • 8.1 Setting up the timer 46
      • 8.1.1 Operating modes 46
      • 8.1.2 Tolerance band 47
      • 8.1.3 Timer start 47
      • 8.1.4 Signal end 48
    • 8.2 Determining the timer run-time 48
    • 8.3 Starting the timer 48
  • 9 BlueControl 49
  • 10 Versions 50
  • 11 Technical data 51
  • 12 Safety hints 55
    • 12.1 Resetting to factory setting 56
• Index
  • 0-9
    • 2-point correction 41
  • A
    • Alarm handling 18 - 19
  • B
    • BlueControl 49
    • Bus interface
      • Technical Data 52
  • C
    • Calibration level (CAL) 41 - 43
    • Certifications 53
    • Configuration examples
      • 2-point controller 31
      • 3-point controller 32
      • 3-point stepping controller 33
      • Continuous controller 34
      • D - Y -Off controller 35
      • Measured value output 36
      • Signaller 30
    • Configuration level
      • Configuration parameters 22 - 28
      • Parameter survey 21
    • Connecting diagram 6
    • Connecting examples
      • di2/3, 2-wire transmitter supply 8
      • INP2 current transformer 7
      • OUT1/2 heating/cooling 7
      • OUT3 as logic output 8
      • OUT3 transmitter supply 8
      • RS485 interface 9
    • Control inputs di1, di2, di3
      • Technical data 51
    • Current signal measuring range 51
  • D
    • Digital inputs di1, di2, di3
      • Configuration 26
      • Technical data 51
  • E
    • Environmental conditions 53
    • Equipment 50
    • Error list 12
  • F
    • Front view 10
  • I
    • Input INP1
      • Configuration 23
      • Parameters 39
      • Technical data 51
    • Input INP2
      • Configuration 23
      • Parameters 39
      • Technical data 51
    • Input scaling 40
  • K
    • Kalibrierung (CAL) 41
  • L
    • LED
      • Ada - LED 10
      • Err - LED 10
      • ì - LED 10
      • LED colours 10
      • ò - LED 10
      • run - LED 10
      • SP.x - LED 10
  • M
    • Maintenance manager 12 - 13
    • Manual tuning 17
    • Mounting 5
  • O
    • Offset correction 41
    • Output OUT1
      • Configuration 24
      • Technical data 52
    • Output OUT2
      • Configuration 25
      • Technical data 52
    • Output OUT3
      • Configuration 25
      • Technical data 52
  • P
    • Parameter setting level
      • Parameter survey 37
      • Parameters 38 - 39
    • Power supply 52
    • Programmer
      • Changing segment end setpoint 45
      • Changing segment time 45
      • Parameter setting 44
      • Set-up 44
      • Starting/Stopping 44
  • R
    • Resetting to factory setting 56
    • Resistance thermometer measuring range 51
  • S
    • Safety hints 55 - 56
    • Safety switch 5
    • Safety test 53
    • Self-tuning
      • Cancelation 15
      • Cancelation causes 16
      • Start 15
    • Set-point processing 29
  • T
    • Thermocouple measuring range 51
    • Timer
      • Display run-LED 48
      • Operating modes 46
      • Signal end 48
      • Timer start 47
      • Tolerance band 47
  • V
    • Versions 50
    • Voltage signal measuring range 51