Fender Cyber Foot Controller User Manual

Page 4

Advertising
background image

w

ww

ww

w.

.f

f e

e n

n d

d e

e r

r.

.c

co

om

m

4

w

ww

ww

w.

. m

m r

r g

g e

e a

a r

r h

h e

e a

a d

d.

.n

ne

et

t

F

F

F

F

e

e

e

e

a

a

a

a

t

t

t

t

u

u

u

u

r

r

r

r

e

e

e

e

s

s

s

s

O

O

O

O

v

v

v

v

e

e

e

e

r

r

r

r

v

v

v

v

ii

ii

e

e

e

e

w

w

w

w

C

C

C

C

y

y

y

y

b

b

b

b

e

e

e

e

r

r

r

r

S

S

S

S

e

e

e

e

r

r

r

r

ii

ii

e

e

e

e

s

s

s

s

M

M

M

M

I

I

I

I

D

D

D

D

I

I

I

I

F

F

F

F

u

u

u

u

n

n

n

n

c

c

c

c

t

t

t

t

ii

ii

o

o

o

o

n

n

n

n

s

s

s

s

The Fender

®

Cyber Foot Controller™ can be used to

send Program Change and Continuous Controller
messages to any MIDI device, hands-free. Especially
designed to complement Fender Cyber-Series™
amplifiers, the Cyber Foot Controller adds functionality
to any amp that interprets the following messages of the
MIDI specification, (features as they relate to Cyber-
Series
amps shown in brackets):

◊ Program Change messages: Use the DOWN and

UP buttons to index by “tens,” then a 0–9 button to
select the “ones” digit. [Selects any preset using the
MIDI map.]

◊ Continuous Controller messages: Use the

CONTINUOUS CONTROLLER pedal to send Control
Change messages. [Adjusts a preset parameter
defined by your amplifier.]

◊ Volume control messages: Use the VOLUME pedal

to adjust the volume on your amplifier. [Adjusts
master volume.]

Cyber-Series™ messages (unspecified MIDI messages
that may be interpreted differently by other amps.)

◊ TAP TEMPO/TUNER BUTTON

•Set the time/rate parameter for the current effect

Activate the on-board tuner.

◊ EFFECTS ON BUTTON

•Engage or bypass the current preset’s effect.

Thank you for choosing Fender

Thank you for choosing Fender

®

®

,

,

—T

—T

one, T

one, T

radition and Innovation—since 1946.

radition and Innovation—since 1946.

A.

TAP TEMPO / TUNER BUTTON
Sets the time/rate parameter for the active effect
with one or more quick presses. A single press will
set the parameter to its maximum value.
or
Activates the TUNER Mode when held down for 2
seconds, (“tun” is displayed). Press any button to
exit TUNER Mode.
Sends a Program Change message to Bank 1,
Program 127.

1

B.

EFFECTS ON (OFF) BUTTON
Alternately engages and bypasses the effects for
the current preset.
Continuous Controller assignment: 85.
Sends alternating Control Change messages:
Data
0 for OFF; Data 127 for ON.

C.

LED DISPLAY
•Displays the last Program Change number

transmitted (flashes “

00_

” until the first

number is selected).

•Displays “tun” in TUNER Mode.
•Displays MIDI Transmit Channel during selection.

D. DOWN (–10) & UP (+10)

BUTTONS
Pre-selects the “tens”
range for a Program
Change number at these
intervals:

0 0 0

010020030

0 4 0

050060070

0 8 0

0901001 10

120

000

(loop)

...

A Program Change number

is not transmitted until the “ones” digit is selected (see
item {E} below). Note: The display stops flashing when a
DOWN or UP selection returns you to the interval
containing the last Program Change number transmitted.

E.

0, 1, 2, 3, 4, 5, 6, 7, 8, 9

BUTTONS

Selects the “ones” digit of the Program Change
number within the pre–selected “tens” range, and
transmits the Program Change number. For
example, if the display shows, “12_,” pressing the
“7” button will cause “127,” to display and the
Program Change 127 to transmit.
Note: 128and 129cannot be selected.

F.

CONTINUOUS CONTROLLER PEDAL
Controls any programmable parameter for the
current preset.
Continuous Controller assignment: 11.
Sends Control Change messages
0–127.

G.

VOLUME PEDAL
Controls the MASTER volume level.
Continuous Controller assignment: 7.
Sends Control Change messages
0–127.

MIDI TRANSMIT CHANNEL SELECTION

Transmit channel is set to 1 by default at power-up. To
select channels (1–16): While holding down

TAP TEMPO/TUNER {A}, press EFFECTS ON {B}, then

release both buttons. Select a channel using the
DOWN and UP buttons {D}, (channel selection is
displayed). Press any “0–9” button to exit.

1

Bank Change #1 is used only to access the TUNER Mode, all other messages ar e prefaced with Bank Change #0, which corresponds

to the MIDI Map on Fender® Cyber-Series™ amplifiers.

Advertising