Fender SRM 8302 - Manual (Page 4)

4
A. EFFECTS - This knob controls
the amount of signal its respective
channel sends to the overall effects
mix. When the knob is set at 0, the
output is “dry”.
B. HIGH - Adjusts the amount of
high frequency boost or cut in the
channel. When all the tone controls
are set at 0 (straight up), the
channel is “flat” with no frequencies
cut or boosted.
C. MID - Adjusts the amount of
middle frequency boost or cut in
the channel.
D. LOW - Adjusts the amount of
low frequency boost or cut in the
channel.
E. MONITOR - This knob controls
the amount of signal its respective
channel sends to the monitor mix.
When the knob is set at 0, the
channel’s signal is not sent to the
monitor bus.
F. LEVEL - Adjusts the volume
control of the individual channel.
Rotating the knob clockwise
increases the respective channel’s
contribution to the “Main Out” mix.
Adjust this control after the MAIN or
overall volume of the SRM 6302 /
8302 has been set.
G. LINE - Plug your instrument in
here. This 1/4 inch TRS balanced
input jack suited for use with items
having a line level output such as
high impedance microphones,
keyboards, drum machines,
outboard effects, etc. It accepts
both balanced and unbalanced
cables
H. MIC - Plug your microphone in
here. This three pin XLR balanced
female input connector is intended
for input signals from low
impedance microphones. Pins 2 and 3 provide
Phantom Power (+48V DC) for condenser style
microphones when the phantom power switch is on.
I. MAIN OUT - This 1/4 inch, TS, unbalanced, line
level output is designed to feed the SRM 6302 /
8302’s main bus signal to an external power
amplifier or main house mixer.
J. PA 1 IN - This 1/4 inch, TS, unbalanced, line
level input jack allows the SRM 6302 / 8302’s power
amplifier #1 (PA 1) to be fed from an external signal
source. When this connection is used, the “main
out” connection to PA 1 is overridden.
K. MON OUT - This 1/4 inch, TS, unbalanced, line
level output is designed to feed the SRM 6302 /
8302’s monitor bus signal to an external power
amplifier or monitor system.
L. PA 2 IN - This 1/4 inch, TS, unbalanced, line
level input jack allows the SRM 6302 / 8302’s power
amplifier #2 (PA 2) to be fed from an external signal
source. When this connection is used, the internal
connection to PA 2 is overridden.
M. EFFECTS OUT/FOOTSWITCH - This 1/4 inch,
TS, unbalanced, line level output jack is designed to
feed the SRM’s effects bus signal to an external
signal processing device, such as a digital delay or a
chorus unit. When a footswitch (P/N 048458,
optional) is inserted into this jack, the SRM’s internal
reverb can be turned on or off remotely.
N. EFFECTS IN - This 1/4 inch, unbalanced, TS, line
level input jack is designed to accept signal from an
external processing device, such as a digital delay or
a chorus unit. The signal entering this jack is mixed
into the Main and Monitor using the “Tape/Effects”
controls labeled “Return to Main” and “Return to
Monitor”.
0 MAX
LEVEL
MONITOR
LOW
MID
HIGH
0 MAX
EFFECTS
LOW
MID
HIGH
0 MAX
+15 15
+15 15
+15 15
INPUT CHANNEL CONTROL FUNCTIONS
A
B
D
C
E
F
MAIN OUT
PA 1 IN
MON OUT EFFECTS OUT/
FOOTSWITCH
PA 2 IN EFFECTS IN
K M I
J L N
INPUT CHANNEL CONNECTIONS
LINE
MIC
G
H
PATCH BAY PANEL CONNECTIONS