Fender SRM 8302 - Manual (Page 5)

A. EQ ASSIGN - This button
switches the graphic equalizer
between the main and the
monitor bus. When this
button is pressed, the EQ is
assigned to the monitor bus.
B. GRAPHIC EQUALIZER -
This 9 band graphic equalizer
consists of active band pass
/ band reject filters spaced at
octave intervals. Moving the
sliders up or down boosts or
cuts the gain at the indicated
frequency.
C. PHANTOM POWER -
When this button is pressed,
a +48V DC Phantom Power
supply is activated, necessary
for some condenser style
microphones. Before
plugging or unplugging any
microphone, make sure the
Phantom Power supply is off.
D. POWER LED - This LED illuminates when the
SRM 6302 / 8302 is on.
E. PA 2 ASSIGN - This button switches the second
power amplifier between the main and the monitor bus.
When this button is pressed, the second power
amplifier is assigned to the monitor bus providing
power to drive monitor speakers. When this button is
in the Main position, the second power amplifier is
assigned to the main bus providing additional power for
front of house enclosures. When connecting the
speakers to your SRM 6302 / 8302, connect one
cabinet to the PA 1 Out jack and the other to the PA 2
Out jack.
F. TAPE/EFFECTS RETURN TO MONITOR -
Adjusts the tape/effects signal level sent to the
monitor mix from either the Effects In or Tape In jacks.
Rotating the knob clockwise increases the tape/effects
signal sent to the monitor mix.
G. TAPE/EFFECTS RETURN TO MAIN - Adjusts
the tape/effects signal level sent to the main mix from
either the Effects In or Tape In jacks. Rotating the
knob clockwise increases the tape/effects signal sent
to the main mix.
H. MAIN - The main output volume control of the
SRM 6302 / 8302. Any adjustments to this control
will affect the signal level at the Main Out, as well as,
PA1 and PA2 depending upon the PA2 Assign
switch position and patch bay configuration.
I. REVERB RETURN TO MONITOR - Adjusts the
amount of reverb signal level sent to the monitor mix.
Rotating the knob clockwise increases the reverb
signal sent to the monitor mix. When the knob is set
at 0, the output is “dry”.
J. REVERB RETURN TO MAIN - Adjusts the
amount of reverb signal level sent to the main mix.
Rotating the knob clockwise increases the reverb
signal sent to the main mix. When the knob is set at
0, the output is “dry”.
K. MONITOR - The monitor output volume control
of the SRM 6302 / 8302. Any adjustments to this
control will affect the signal level at the Mon Out, as
well as, PA1 and PA2 depending upon the PA2
Assign switch position and patch bay configuration.
L. EFFECTS - Adjusts the signal level present at the
Effects Out / Footswitch jack, as well as, the signal
driving the reverb. Rotating the knob clockwise
increases the amount of tape/effects and reverb drive
signal. When the knob is set at 0, there is no effects
drive signal.
M. REC OUT - Adjusts the tape out signal level of
the SRM 6302 / 8302. (The Main Out signal feeds
this control.) Rotating the knob clockwise increases
the output level. When the knob is set at 0, there is
no signal level output.
5
MASTER CONTROL PANEL FUNCTIONS
0 MAX
0 MAX
0 MAX 0 MAX 0 MAX
0 MAX
0 MAX
0 MAX
MAIN
RETURN
TO MAIN
RETURN
TO MONITOR
MONITOR EFFECTS
63 125 250 500 1k 2k 4k 8k 16k
12dB
+12dB
OdB
12dB
+12dB
OdB
REC OUT
RETURN
TO MONITOR
RETURN
TO MAIN
GRAPHIC EQUALIZER
TAPE/
EFFECTS
REVERB
PHANTOM POWER
PA 2 ASSIGN
EQ ASSIGN POWER
MAIN
MON
OFF
ON
MAIN
MON
A
I F
H
G J
K L M
B
C
D
E