Freestyle Navigator 2.0 - Manual (Page 2)

To reduce carbon foot print, these
Freestyle instructions are printed with
soy inks on recycled paper.
ENGLISH
TO USE THE RECALL FUNCTION:
1. Press S3 button to select RECALL
mode.
2. Press S1 button to scroll through
the recorded individual lap time and
total elapsed time.
NOTE: The recall function is available
only when there is lap record. The
message “NO LAPS” will be displayed
if there is no lap record.
NOTE: The lap record will be cleared
when the chronograph is reset.
TO SET THE TIMER:
1. Press S3 button to select TIMER
mode.
2. Press and hold S2 button for
around 2 seconds, the timer selec
tion will blink.
3. Press S1 button to toggle between
timer interval 1 and timer interval 2
to set.
4. Press S3 button, the second digits
will blink.
5. Press S1 button to set the second
digits. Holding down the button will
speed up the process.
6. Press S3 button, the minute digits
will blink.
7. Press S1 button to set the minute
digits. Holding down the button will
speed up the process.
8. Press S3 button, the hour digits will
blink.
9. Press S1 button to set the hour
digits. Holding down the button will
speed up the process.
10. Press S3 button, the action-at-end
selection will blink.
11. Press S1 button to select among CS
(Count Stop), CR (Count Repeat)
and CCU (Count Up).
12. After finished making all the set-
tings, press S2 button to confirm.
NOTE: Illustration of the action-at-end
selections:
a) CS (Count Stop) – the timer will
stop when the countdown teaches
zero.
b) CR (Count Repeat) – the timer
will repeat the countdown when the
countdown reaches zero.
c) CCU (Count Up) – the timer count
up to a maximum of 23 hours 59
minutes and 59 seconds when the
countdown reaches zero.
NOTE: The timer cannot be activated
if the value of timer interval 1 is set
as 0:0’00”.
TO USE THE TIMER:
1. Press S3 button to select TIMER
mode.
2. The timer will be displayed in its
current state – reset, running, or
stopped.
3. To resume a counting, press S1
button to resume from where it left
off.
4. To start a new counting, reload the
timer first.
Press S1 button to stop counting
and then press S2 button.
5. After reaching zero in a countdown,
a tune will be emitted. To stop the
tune, press any button.
NOTE: You can leave the timer running
while switching over to other operating
modes.
TO SET THE ALARM:
1. Press S3 button to select ALARM
mode.
2. Press S2 button to select among
alarm entries 1, 2 and 3 to set.
3. Press and hold S2 button for around
2 seconds. The minute digits will
blink.
4. Press S1 button to set the minute
digits. Holding down the button will
speed up the process.
5. Press S3 button, the hour digits will
blink.
6. Press S1 button to set the hour
digits. Holding down the button will
speed up the process.
7. Press S3 button the alarm fre
quency will blink.
8. Press S1 button to select among
daily (DL Y) and individual day (of
the week) only – Sunday (SUN),
Monday (MON, Tuesday (TUE),
Wednesday (WED), Thursday (THU),
Friday (FRI) and Saturday (SAT).
9. After finished the settings, press S2
button to confirm.
NOTE: The alarm will automatically be
activated after being set.
NOTE: The alarm will work according
to HOME TIME or FOREIGN TIME (de-
pends on your selection in time mode).
TO USE THE ALARM:
In ALARM mode,
1. Press S2 button to select among
alarm entries 1, 2 and 3 to set.
2. Press S1 button to activate the
alarm. The alarm indicator will
be displayed.
3. Press S1 button again to deactivate
the alarm. The message “OFF” will
be displayed.
WHEN AN ALARM GOES OFF:
A 20-second alarm tune will be emitted
at the designated time when the alarm
is activated. To stop the tune, press
any button.
TO USE THE BACKLIGHT:
Press S4 button to turn on the back-
light for around 3 seconds.
BEZEL-ACTIVATED BACKLIGHT
FUNCTION:
1. Press and hold S4 button for around
3 seconds activated or deactivate
the bezel-activated backlight func-
tion.
2. When the function is activated, the
light bulb icon will be displayed.
You can then turn on the backlight
for around 3 seconds by touching
the bezel of the watch.
NOTE: To use the bezel-activated
backlight function, the caseback of the
watch must be in direct contact with
your skin during wear.
LOW BATTERY DETECTION:
When the battery of the watch is close
to depletion, the battery low indicator
will be displayed.
FS8127-NA
VIG
AT
OR
2.0-1067-MR01