Multi-Tech Systems MT5600SMI-34 - Manual (Page 132)

Index
Multi-Tech Systems, Inc. SocketModem MT5600SMI Developer’s Guide 132
call waiting enable command +PCW, 71
Caller ID command +VCID, 30
Carrier loss disconnect time, setting S10, 76
CI signal indication command, 64
Command mode, 29
Command string, 29
Communications programs, 29
compromise equalizer enable command
:E, 70
connect message control command W, 36
Country code how to set, 114
Country codes supported, 114
country of installation command +GCI, 32
current and power requirements, 15
D
data compression command +DS, 60
data compression reporting command +DR, 61
Data mode, 29
Design considerations, 121
Vendor recommendations, 119
designate a default reset profile command &Y, 33
Dial command D, 41
disconnect (hang up) command H, 43
Disconnect delay S10, 76
display current configuration and stored profiles
command &V, 45
display last connection statistics command &V1, 46
DSR override command &S, 39
DTE-modem local flow control command +IFC, 40
DTE-modem local rate reporting command +ILRR, 40
DTR option command &D, 38
E
echo command E, 36
Electrical Characteristics, 13
Electromagnetic Interference Considerations, 122
EMC, Safety, and R&TTE Directive Compliance, 130
enable cellular power level adjustment command )M,
70
enable quick connect profile save command -QCPS,
74
enable/disable data compression command %C, 62
enable/disable line quality monitor and auto-retrain or
fallback/fall forward command %E, 53
error control and synchronous mode selection
command +ES, 55
error control reporting command +ER, 57
Escape character S2, 75
Escape sequence, 29
Examples of calling/answering table, 98
extended result codes command X, 37
F
FastConnect control command $F, 71
Fax adaptive reception control parameter +FAR, 94
fax answering, 87
Fax carrier loss timeout parameter +FCL, 94
Fax Class 1 and 1.0 auto answer enable command
+FAA, 90
Fax Class 1 and Fax Class 1.0 Commands Table, 87
Fax Class 1.0 auto answer enable command +FAA,
90
Fax Commands
+FAA, 90
+FAE, 90
+FAR, 94
+FCL, 94
+FCLASS=1, 90
+FCLASS=1.0, 90
+FDD, 95
+FIT, 95
+FLO, 97
+FMI?, 96
+FMM?, 96
+FMR?, 96
+FPR, 96
+FRH, 93
+FRM, 92
+FTH, 92
+FTM, 91
+FTS, 90, 91
fax control reception, 88
fax control transmission, 87
fax data reception, 89
fax data transmission, 89
Fax double escape character replacement
+FDD, 95
Fax DTE inactivity timeout parameter +FIT, 95
Fax fixed DTE rate parameter +FPR, 96
Fax flow control parameter +FLO, 97
fax I/O processing, 86
fax origination, 87
Fax receive data with HDLC framing command +FRH,
93
Fax Receive Facsimile +FRM, 92
Fax Receive Silence +FRS, 91
fax request manufacturer identification parameter
+FMI?, 96
Fax request model identification parameter +FMM?,
96
Fax request revision identification parameter +FMR?,
96
Fax Transmit Data with HDLC Framing +FTH, 92
Fax Transmit Facsimile +FTM, 91
Fax transmit silence command +FTS, 90
FCC Regulations, 124
fixed DTE rate command +IPR, 39
flow control command &K, 38
force full startup procedure on next connection
command +QCPC, 74
H
Handling Precautions, 13
Hangup delay S10, 76
I
identification command I, 31
initial cellular power level setting command @M, 70
Initialization strings, 29
initiate modem-on-hold command +PMHR, 72
International Modem Restrictions, 130
Interrupt enable register, 20
Interrupt Sources and Reset Control Table, 22
L
Label content and format, 126
last call status report command #UD, 65