Marantz SR6400 - Manual (Page 29)

26
ENGLISH
(Using the remote control unit)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMO button on the remote. “– –“
(preset number) starts blinking on the display.
3.
Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for
example), either input “02” or just input “2” and
wait for a few seconds.
RECALLING A PRESET STATION
(Using the SR6400)
1. Press the F/P button to show the preset
station on the display.
2. Select the desired preset station by pressing
the TUNING
or buttons on the front panel.
(Using the remote control unit)
1.
Press the 4 or ¢ buttons to select the desired
preset station, or input your desired preset
channel with the numeric buttons on the
remote.
PRESET SCAN
(Using the remote control unit)
1. Press the P.SCAN on the remote.
“PRESET SCAN” appears on the display and
then the preset station with the lowest preset
number is recalled first.
2. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
3. You can fast forward the preset stations by
pressing the
¢ continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CL button or P.SCAN on the remote.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
1. Recall the preset number to be cleared with the
method described in “Recalling” a preset station.
2.
Press the MEMORY button on the front panel or
press the MEMO button on the remote.
3.
The stored preset num blinks in the display
for 5 seconds. While blinking, press the CLEAR
button on the front panel or press the CL button
on the remote.
4.
“xx CLEAR” appears on the display to indicate
that the specified preset number has been
cleared.
Notes:
• To clear all stored preset stations, press and hold
the CLEAR and the F/P buttons for two seconds.
AV SURROUND RECEIVER SR6400
UP
SELECTOR VOLUME
DOWN MEMORY TUNING MODE CLEAR
MUTE
POWER ON/STANDBY PHONES
ENTER
STANDBY AUX INPUT S-VIDEO VIDEO L AUDIO R
ATT SELECT
DSS/VCR2 AUX VCR1 DVD TV CD CD-R TAPE TUNER
S-DIRECT DISPLAY A/D 6.1CH INPUT SPEAKERS A/B
F/P
2. 1.
1.
1.
3.
1.
3.
3.
2.
V SURROUND RECEIVER SR6400
MEMORY TUNING CLEAR
PHONES
ENTER
DSS/VCR2 AUX VCR1 DVD TV CD-R
S-DIR A/D 6.1CH INPUT SPEAKERS A/B
2. 3.
SORTING PRESET STATIONS
If you have stations memorized, and there is a gap
in the sequential order:
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre
sets for 4-9), you can have pre set 10 become pre
set 5:
To sort the numbers, press and hold the MEMORY
and the F/P buttons.
“PRESET SORT” will appear on the display and
sorting will be done.
NAME INPUT OF THE PRESET STATION.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
1. Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.
2. Press the MEMORY button on the front panel
or press the MEMO button on the remote for
more than 3 seconds.
3. The left most column of the station name
indicator flashes, indicating the character
entry ready status.
4. When the SELECT knob is turned or you press
the
5 5 5 5 5 / 6 6 6 6 6 buttons on the remote, alphabetic
and numeric characters will be displayed in the
following order:
A
→ B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
UP →
← DOWN
5.
After selecting the first character to be entered,
press the MEMORY or ENTER buttons, press
the MEMO button on the remote.
The entry in this column is fixed and the next
column starts to flash. Fill the next column the
same way.
To move back and forth between the characters,
press the TUNING
/ buttons or press the 4
or ¢ buttons on the remote.
Note:
• Unused columns should be filled by entering
blanks.
6.
To save the name, press the MEMORY or the
ENTER button, press the MEMO button on
the remote for more than 2 seconds.
AV SURROUND RECEIVER SR6400
UP
SELECTOR VOLUME
DOWN MEMORY TUNING MODE CLEAR
MUTE
POWER ON/STANDBY PHONES
ENTER
STANDBY AUX INPUT S-VIDEO VIDEO L AUDIO R
ATT SELECT
DSS/VCR2 AUX VCR1 DVD TV CD CD-R TAPE TUNER
S-DIRECT DISPLAY A/D 6.1CH INPUT SPEAKERS A/B
F/P
AV SURROUND RECEIVER SR6400
UP
SELECTOR VOLUME
DOWN MEMORY TUNING MODE CLEAR
MUTE
POWER ON/STANDBY PHONES
ENTER
STANDBY AUX INPUT S-VIDEO VIDEO L AUDIO R
ATT SELECT
DSS/VCR2 AUX VCR1 DVD TV CD CD-R TAPE TUNER
S-DIRECT DISPLAY A/D 6.1CH INPUT SPEAKERS A/B
F/P
5. 2. 5. 6. 5. 6. 4. 4.
4.
5.
4.
2.
5.
6.
Ten keypad Press, press again, press again, etc.
1 A → B → C → 1 → A
2 D → E → F → 2 → D
3 G → H → I → 3 → G
4 J → K → L → 4 → J
5 M → N → O → 5 → M
6 P → Q → R → 6 → P
7 S → T → U → 7 → S
8 V → W → X → 8 → V
9 Y → Z → space → 9 → Y
0 – → + → / → 0