Maytag 8113P636-60 - Manual (Page 11)

10
Oven Cooking
Baking
To set bake:
1. Press the Bake pad for desired oven.
• “Bake” will flash.
• “000°” will flash in the display.
2. Select the oven temperature. The oven
temperature can be set from 170° to 550°. Press
or press and hold the More+ or Less- pad.
• “350°” will light when either pad is first pressed.
• Press the More+ pad to increase the temperature.
• Press the Less- pad to decrease the temperature.
3. Press Bake pad again or wait four seconds.
• “Bake” will stop flashing and light in the display.
• “Preheat” will light in the display.
• 100° or the actual oven temperature will display. The
temperature will rise in 5° increments until the preset
temperature is reached.
4. Allow 4-10 minutes for upper oven to preheat and 7-12
minutes for lower oven to preheat.
• When the set oven temperature is reached, one long
beep will sound.
• To recall the set temperature during preheat, press the
Bake pad.
Setting Upper and Lower
Oven Functions
Notes:
• If the lower oven is NOT in use, the upper oven will
preheat more quickly.
• Allow at least 1 /
2
-inch between the baking pan or
casserole and the top element in the upper oven.
Loaf, angel food or bundt pans are not recommended in
the upper oven.
• Do not use temperatures below 140° F to keep food warm
or below 200° F for cooking. For food safety reasons, lower
temperatures are not recommended.
• The back part of the lower oven bake element will NOT
glow red during baking. This is normal.
• When baking frozen, self-rise pizzas in the upper oven,
place the pizza on a cookie sheet to avoid overbrowning.
• When preheating with a baking/pizza stone inside
the upper oven, do not set oven above 400 ° F. To use
baking/pizza stones at temperatures above 400 ° in
the upper oven, put stone in after the preheat beep.
• To change the oven temperature during cooking, press the
Bake pad and then the More+ or Less- pad until you
reach the desired temperature.
• If you forget to turn off the oven, it will automatically turn
off at the end of 12 hours. If you wish to deactivate the
Automatic Shut-Off/Sabbath Mode feature, see page 14.
Return To Factory Default
Settings
The control can be reset to the factory default settings. To
return to the default settings:
1. Press and hold upper oven Keep Warm and CANCEL
pads for three seconds. A single beep will sound and “dEF”
(default) will appear in the display.
2. Press the More+ pad to choose the factory settings. “cLr”
(clear) will appear in the display.
3. Wait four seconds and the factory settings will be accepted.
4. If the More+ or Less- pad is not pressed within 30 seconds,
the control will return to the existing settings.
To change the oven temperature during preheat, press
Bake once and reset temperature.
5. Place food in the oven.
6. Check cooking progress at minumum cooking time. Cook
longer if needed.
7. When cooking is finished, press
CANCEL pad.
8. Remove food from the oven.
Baking Differences Between Your Old
and New Oven
It is normal to notice some baking time differences between a
new oven and an old one. See Adjusting the Oven Temperature
on page 15.
Cook & Hold
Cook & Hold allows you to bake for a preset amount of time,
followed by a one-hour Keep Warm cycle.
To set Cook & Hold:
1. Press the Cook & Hold pad once for upper
oven or twice for lower oven.
• “Bake” and “Hold” flash.
• “000°” will flash in the display.
Cont.
4. If the More+ or Less- pad is not pressed within 30
seconds, the control will return to the existing settings.