Marantz CDR510 - Manual (Page 23)

- 23 -
CDR
GROUND
ANALOG
IN OUT
L
R
INPUT SELECT
L R
BALANCED IN
R - TRIM - L
0 +22 0 +22
(REF=+16dBu/0dBFS)
HOT(+)
COLD(-)
RS232C
CD
ANALOG DIG
OUT OUT
R
L
IN IN OUT
LOOP
OUT
DIGITAL
(SPDIF)
SERIAL NO.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECRIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
INT.(IR)
EXT.
IN
OUT
REMOTE (RC5)
MODEL NO. CDR510/U1B AC120V 60HZ 0.5A
M A R A N T Z A M E R I C A I N C . 1 1 0 0 M A P L E W O O D D R I V E I T A S C A , I L 6 0 1 4 3
COMPLIES WITH FDA RADIATION PERMORMANCE
STANDARDS, 21CFR SUBCHAPTER J
MANUFACTURED
WARNING: SHOCK HAZARD - DO NOT OPEN
AVIS : RISQUE DE CHOC ÉLECTRIQUIE - NE PAS OUVRIR.
MML
AC IN
RISK OF ELECTRIC SHOCK DO NOT OPEN
MADE IN JAPAN
UL
C US LISTED AUDIO SYSTEM 69FM
CAUTION
FACTORY CODE NO 4300
CDR
GROUND
ANALOG
IN OUT
L
R
INPUT
SELECT
L R
BALANCED
IN
R - TRIM - L
0 +22 0 +22
(REF=+16dBu/0dBFS)
HOT(+)
COLD(-)
3
3. BALANCED IN (continued)
The three pin XLR connection permits trimming,
adjusting the input level. See TRIM (4).
The INPUT SELECT SWITCH (6) on the rear of
the CDR510 must be to the left to select the
BALANCED IN inputs. ANALOG must also be
selected by pressing and releasing the INPUT
button on the front of the CDR510 so ANALOG is
displayed.
1
ANALOG CD - R L
R
TOTAL
CD
CHANGER
Example
display
ANALOG
The pin out for the XLR jacks is printed on the
CDR510 for easy reference:
Pin 1 ground,
Pin 2 HOT +,
Pin 3 COLD -.
4
4. TRIM R & L
You can use a small screw-
driver to adjust the TRIM of
the XLR L & R inputs.
R - TRIM - L
0 +22 0 +22
(REF=+16dBu/0dBFS)
The TRIM is factory preset at +16 dBu with an
adjustment range from 0 to +22 dBu.
Some professionals prefer to first set the TRIM
using a meter and to do a fine adjustment by
listening for distortion and watching the level
meters on the CDR510.
5
ANALOG
IN OUT
L
R
5. ANALOG IN / OUT
jacks
RCA jacks for line level
input and output to the
CDR drive.
L & R ANALOG IN jacks
Plug L and R RCA jacks in here to connect to the
Line level output jacks of an external pre-ampli-
fier, mixer or other audio device.
The INPUT SELECT SWITCH (6) on the rear of
the CDR510 must be to the left to select the
BALANCED IN inputs. ANALOG must also be
selected by pressing and releasing the INPUT
button on the front of the CDR510 so ANALOG
is displayed.
6
Example
display
L & R ANALOG OUT jacks
Plug L and R RCA jacks in here to connect to the
Line level input jacks of an external pre-amplifier,
mixer or other audio device. This output is always
on when there is play back on the CDR drive.
1
ANALOG CD - R L
R
TOTAL
CD
CHANGER
ANALOG
6. INPUT SELECT switch
This switch selects between
the BALANCED IN (XLR)
jacks and the ANALOG IN
(RCA) jacks for analog input
for recording on the CDR
drive.
INPUT
SELECT
IN
ANALOG must also be selected by pressing and
releasing the INPUT button on the front of the
CDR510 so ANALOG is displayed.