Marantz SR9200 - Manual (Page 49)

45
ENGLISH
MULTI ROOM SYSTEM
The Multi Room system is a function which allows you to listen to the
same or a different source in a room other than the room in which the
SR9200 is located.
To use this function, a multi room remote unit and remote control
signal receiver available from your Marantz dealer are necessary.
The operations possible with the multi room function are explained
briefly below.
For details, refer to the instruction manual supplied with the multi room
remote control unit and receiver.
When the outputs of the MULTI ROOM OUT terminals are wired and
connected to amplifiers installed in other rooms or MULTI SPEAKER
OUT terminals are wired and connected to L&R speakers in other
room, different sources can be played in rooms other than the main
room in which this unit and the playback devices are installed.
SR9200 has some feature to MULTI ROOM SYSTEM as source
selector, OSD information, sleep timer, Multi Room Speaker output
and remote control.
MULTI ROOM PLAYBACK USING THE
MULTI ROOM OUT TERMINALS
The SR9200 is equipped with audio pre-out terminals for which the
volume is adjustable and composite video output terminals as the
MULTI ROOM output terminals.
A separately sold stereo power amplifier (PM8100) can be connected
to enjoy multi room playback.
Operation to MULTI ROOM OUT without the remote controller.
1.
Press the MULTI button. The unit enters multi room mode and the
display indicates “ SELCT SOURCE ” and flashes the “ MULTI ”
indicator for approx. 10 seconds.
2.
In this time, you can select the input source by pressing the input
selector buttons.
Then, the display indicates “
MULTI VOL ” “ VOLUME xx dB ” for
approx. 5 seconds.
3.
During this time, you can set the volume level in the multi room as
desired.
This will only set the volume in the second room.
4.
If you desire to set sleep timer to multi room, press SLEEP button
to setup the time.
MULTI ROOM PLAYBACK USING THE
MULTI SPEAKER TERMINALS
The SR9200 allows you to connect another set of speakers and place
them in a different room or separated area for listening to music.
Operation to MULTI ROOM SPEAKER without the remote controller.
1.
Press the MSPK button. The unit enters multi room mode and the
display indicates “ SELCT SOURCE ” and flashes the “ MULTI ” &
“ M-SPKR ” indicators for approx. 10 seconds.
2.
In this time, you can select the input source by pressing the input
selector buttons.
3.
Then, the display indicates “ MULTI VOL ” “ VOLUME xx dB ” for
approx. 5 seconds.
During this time, you can set the volume level in the multi room as
desired.
This will only set the volume in the multi room.
4.
If you desire to set sleep timer to multi room, press SLEEP button
to setup the time.
Notes for MULTI ROOM SPEAKER
• MULTI ROOM SPEAKER On/ Off is available in main room
only.
• You can not play the source in 7.1ch playback mode as THX-
Surr EX, DTS-ES in the main zone, when MULTI ROOM
SPEAKER is active.In other words, the condition of main room
is same as "Surr Back Speaker = None" setting.
• You can not turn MULTI SPEAKER on, when you set Speaker
setup in OSD menu.
OPERATION TO MULTI ROOM OUTPUTS
WITH THE REMOTE CONTROLLER FROM
SECOND ROOM.
1.
Tap the MULTI ROOM on on multi room remote control unit from
the MULTI ROOM.
This operations will put the SR9200 into multi room mode and
“
MULTI ” will light in the display.
MULTI ROOM Video output will show OSD information to
condition of MULTI ROOM setup.
2.
Press the VOL + or VOL – button on the multi room remote control
unit to set the desired sound volume.
3.
In multi room mode, the multi room remote control unit can be
used in the multiroom to operate the following functions.
General:
Controlling volume level, sleep timer, and muting. Selecting
input audio and video source
Tuner:
Selecting band, controlling preset channel up and down, tuning
up and down, direct frequency call.
Notes for multi room system:
• The MULTI ROOM OUT and MULTI SPEAKER terminals are
analog outputs.
These are not support to digital signals input.
If no sound is heard from the selected input source, check if the
component is connected to the analog inputs.
• If Tuner (FM or AM) is active in main room, you can not
control any function of tuner.
In this case, You can listen the same condition as main room.
POWER ON/STANDBY
STANDBY
VOLUME
UP DOWN
PHONES
SELECT MUTE ATT ENTER
SELECTOR
7.1CH-IN
LD DSS TAPE CD-R TUNER CD TV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1 S-DIRECT
AUX2 A/D
SLEEP
AUTO-TUNE GYRO TUNING DOWN UP T-MODE F/P
AUX1 INPUT R AUDIO L VIDEO S-VIDEO DIGITAL
MEMO CLEAR DISPLAY
DVD
1. 3. 4.
POWER ON/STANDBY
STANDBY
VOLUME
UP DOWN
PHONES
SELECT MUTE ATT ENTER
SELECTOR
7.1CH-IN
LD DSS TAPE CD-R TUNER CD TV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1 S-DIRECT
AUX2 A/D
SLEEP
AUTO-TUNE GYRO TUNING DOWN UP T-MODE F/P
AUX1 INPUT R AUDIO L VIDEO S-VIDEO DIGITAL
MEMO CLEAR DISPLAY
DVD
1. 3. 2. 4.
MU L T I ROOM
MU L T I ROOM : O F F
MU L T I S P KR : O F F
V I D EO : D V D
A UD I O : D V D
V O L UME S E T U P : V AR I AB L E
V O L UME L E V E L : - 9 0 d B
S L E E P T I ME R : O F F
- - - - MA I N - ROOM S T A T U S - - - -
V I D EO : D V D
AUD I O : D V D
MA I N E X I T
1.