Marantz SR7500 - Manual (Page 19)

15
ENGLISH
AC IN
MULTI
OUT
TV DVD
C
IN OUT
S-VIDEO
DVD DSS/VCR2
C
RS-232C
MULTI RC
IN OUT DSS/VCR2 IN OUT OUT VCR1
VCR1
L
SBR
SBL
OUT
PRE
SL L
SR R
DSS/VCR2 DVD TV
R
IN
R SW
RC-5
IN
SR
AUDIO
7.1CH
IN
OUT IN
L SL
SBR
SBL CD
IN OUT SW OUT
CDR/MD TAPE
OUT IN
IN OUT
VIDEO
MONITOR OUT MULTI VCR1 TV OUT
(AUX2)
MONITOR
DIGITAL IN DIGITAL OUT
4
1 OPT. 2
5
3
6 COAX.
R L R R
FRONT A
L L
FM (75 Ω )
ANTENNA
GND AM
COMPONENT VIDEO
CB/PB CR/PR CR/PR CR/PR CB/PB CB/PB TV Y Y
MONITOR OUT
VCR1
DVD DSS/VCR2
Y
SURROUND
100W MAX.
AC OUTLET
SWITCHED 230V 50/60H Z
OUT
SPEAKER SYSTEMS
FRONT A OR B, CENTER, SURR, SURR BACK
: 6 - 8 OHMS FRONT A + B : 8 OHMS
FLASHER IN
DC OUT 1 2
1 2
R L
FRONT B CENTER
SURROUND BACK/ MULTI SPEAKER/ SPEAKER C
ON
OFF SPEAKER C
OUTPUT INPUT-2 INPUT-1 USB IN DVI-D
C
SR R
7.1CH
IN
L SL
SBR
SBL
SW
C
SBR
SBL
OUT
PRE
SL L
R SW SR
L
R
FRONT SURR. SURR.
BACK
SUB
WOOFER
CENTER
L
R
FRONT SURR. SURR.
BACK
SUB
WOOFER
CENTER
R L R L R L
L R
R L
L R L R
R L
R L R L R L
R L
ADVANCED CONNECTING
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio
source such as a SACD multichannel player, DVD
audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the
SETUP MAIN MENU. See page 23.
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.
POWER
AMPLIFER
DVD AUDIO PLAYER
or
SACD MULTI CHANNEL
PLAYER
Center Front
Left Front
Right
Surround
Left Surround
Right
Subwoofer
Surround
Back Left
AC IN
MULTI
OUT
TV DVD
C
IN OUT
S-VIDEO
DVD DSS/VCR2
C
RS-232C
MULTI RC
IN OUT DSS/VCR2 IN OUT OUT VCR1
VCR1
L
SBR
SBL
OUT PRE
SL L
SR R
DSS/VCR2 DVD TV
R
IN
R SW
RC-5 IN
SR
AUDIO
7.1CH IN
OUT IN
L SL
SBR
SBL CD
IN OUT SW OUT
CDR/MD TAPE
OUT IN
IN OUT
VIDEO
MONITOR OUT MULTI VCR1 TV OUT
(AUX2)
MONITOR
DIGITAL IN DIGITAL OUT
4
1 OPT. 2
5
3
6 COAX.
R L R R
FRONT A
L L
FM (75½)
ANTENNA
GND AM
COMPONENT VIDEO
CB/PB CR/PR CR/PR CR/PR CB/PB CB/PB TV Y Y
MONITOR OUT
VCR1
DVD DSS/VCR2
Y
SURROUND
100W MAX.
AC OUTLET
SWITCHED 230V 50/60H Z
OUT
SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : 6 - 8 OHMS FRONT A + B : 8 OHMS
FLASHER IN
DC OUT 1 2
1 2
R L
FRONT B CENTER
SURROUND BACK/ MULTI SPEAKER/ SPEAKER C
ON
OFF SPEAKER C
OUTPUT INPUT-2 INPUT-1 DVI-D
RC-5
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL EXTERNAL INTERNAL EXTERNAL INTERNAL
1
RC OUT
2
CONNECTING THE REMOTE CONTROL JACKS
MD DECK CD RECORDER
q
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the
remote signal only to the unit. Also, if a Marantz
power amplifier (some models excluded) is
connected to one of these terminals, the power
amplifier’s, power switch is synchronized with this
unit’s power switch.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for
this feature.
CD PLAYER
OPTION
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR7500,
be sure to always disable operation of the infrared
sensor on the main unit by using the following
procedure.
1. Hold down the MULTI button and the MENU
button on the front panel at the same time for
five seconds.
2. The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3. Press the CURSOR buttons ( , ) to change
this to “IR=DISABLE”.
4. Press the ENTER button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
• Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not
connected. Otherwise, the main unit will be
unable to receive remote control commands.
5. To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
Surround
Back Right