Learn, Use page, English – Marantz SR7500 User Manual

Page 43

Advertising
background image

39

ENGLISH

ENGLISH

BASIC OPERATION

USE MODE

(Normal operation status)

This remote control is preset with a total of 12
types of remote codes, including Marantz TV
(television), DVD, VCR (VCR deck), DSS (satellite
broadcasting tuner), TUNER, CD, CD-R, MD,
TAPE (tape deck), AUX1, AUX2, and AMP
(amplifier).
Learning is not necessary for Marantz products.
You can use these products without setting any
codes.

1.

Press the

SOURCE

button.

For this example, press DVD.
DVD is shown on the LCD, and the remote control is
set for DVD.
Pressing the source button once changes the remote
control to the settings for the source that was
pressed.
To change the amplifier or other source, press the
SOURCE button twice (double-click). The code is
sent, and then the amplifier source changes to DVD.

2.

Press the buttons to operate the DVD.

The

indicator is shown on the LCD while the

remote control codes are being transmitted. It is not
displayed when buttons without stored code are
pressed.

3.

The direct buttons can be used to perform up
to 20 operations for each of the 12 sources,
including DVD, TV, AMP, and other AV
equipment.

The buttons consist of the D1 to D5 buttons, and the
equipment is operated by pressing the buttons
corresponding to the indicators on the LCD.
Four pages are available, and press the

>

button to

select a page. The current page position is displayed
on the LCD.

PRESET MODE

(When operating non-Marantz AV equipment
products)

This remote control is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, VCR, LD, CABLE, DSS,
DVD, TAPE, TUNER, CD, CD-R, MD and AMP.
Settings can be made in one of two ways.
When the preset codes are set, the following
codes are contained in the source button of the
remote control.

See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers,
and other settings.

• When using Marantz products, TV and DVD can

be set to TV1 (TV/VDP: Projector) and TV2
(PDP: Plasma display), and DVD1 (first DVD
player) and DVD2 (second DVD player),
respectively, to match the customer’s operating
environment. These settings are made in
PRESET mode.

In the factory default state, the remote control is
set to TV1 and DVD1. To make the presets,
enter the numbers below while referring to the
section “Entering and Setting the Manufacturer
Number Directly”.

TV1:

0001,

TV2:

0002

DVD1: 0001,

DVD2: 0002

Entering and Setting the Manufacturer Number
Directly

Refer to the manufacturer number list.
This example shows how to set a SAMSUNG DVD
player.

1.

View the supplied manufacturer number list,
and find the number of the manufacturer for
the device that you are using.

2.

Hold down the

M

button for three seconds or

more.

The menu is displayed.

3.

Press the

D1

(PRESET) direct button.

The Preset setting (P-SET) is displayed.

4.

Press the

DVD

source button.

5.

Press the numeric buttons to enter the four-
digit manufacturer number.

Example: To enter “0600” from the manufacturer

number list.

To correct the entered number, use the

or

cursor button to enter the correct number.

• If no button is pressed for over one minute

during the setting process, any settings
that were made are cancelled.

6.

Press the

OK

cursor button.

7.

Confirm the OK is displayed and then the
display returns to the Preset Setting (P-SET).

When the manufacturer number is entered correctly,
OK is displayed momentarily on the screen.

• I f y o u e n t e r a n u m b e r n o t i n t h e

manufacturer number list, WRONG CODE
is displayed, and then you return to the
preset setting again

Check the manufacturer number list, and
either set a different number or use the
sequence function to set.

8.

To set the manufacturer number for another
source device, repeat the procedure in steps 4
to 6.

9.

After the settings are completed, press the

M

button.

10.

Press the buttons on the remote control to
check that the DVD can be operated correctly.

Setting Equipment Not Appearing in Manufacturer
Number List

Use the sequence function to set equipment not
appearing in the manufacturer number list. You
may still be unable to set some equipment even
when using the sequence function. In this case,
the remote control can be programmed with codes
individually.
In the sequence function, the power ON/OFF
codes are transmitted by pressing the remote
control buttons in order.
If the power for the equipment is left on, hold down
the button until the equipment is turned off, and
then release. This completes the setting.

This example shows how to set a DVD player.

1.

Turn on the power of the DVD player.

2.

Hold down the

M

button for three seconds or

more.

The menu is displayed.

3.

Press the

D1

(PRESET) direct button.

The Preset setting (P-SET) is displayed.

4.

Press the

DVD

source button.

5.

Hold down the

CH+

or

CH–

button for one

second or more.

6.

Press the

CH+

button repeatedly in the

interval for one second.

The signal is transmitted, and the display cycles
through the code number.
Press the

CH–

button to go back to a number screen.

7.

Release the button once the DVD player turns
off.

8.

Press the

OK

cursor button.

9.

Confirm the OK is displayed and then the
display returns to the Preset Setting (P-SET).

10.

To set the manufacturer number for another
source device, repeat the procedure in steps 4
to 8.

11.

After the settings are completed, press the

M

button.

12.

Press the buttons on the remote control to
check that the DVD can be operated correctly.

Check the following points if the equipment which
was set does not operate properly.
• If there is more than one number in the

manufacturer number list, try setting a different
number.

• There may be some buttons which cannot be

used. Program the codes to the required
buttons.

Remote control

Corresponding

Device name

source name

preset code

TV

TV

Television

DVD

DVD

DVD player

VCR

VCR

Video deck

DSS

SATELLITE

Satellite broadcasting
tuner equipment

TUNER

RECEIVER/TUNER

AM FM TUNER

CD

CD/CD-R PLAYER

CD player

CD-R

CD/CD-R PLAYER

CD recorder

MD

CD/CD-R PLAYER

MD deck

TAPE

TAPE

Cassette deck

AUX1

CABLE

Cable television

AUX2

LASER DISC

Laser disc player

AMP

AMPLIFIER

Amplifier or receiver

RECEIVER/TUNER

LEARN

1 2

LEARN

1 2

LEARN

1 2

4

5

7

USE

PAGE

1

LEARN

1 2

LEARN

1 2

LEARN

1 2

LEARN

1 2

5

6

2

3

4

Advertising
This manual is related to the following products: