Marantz SR4300 - Manual (Page 18)

14
ENGLISH
DIGITAL DIGITAL
IN IN
OUT OUT
DIG-1 IN DIG-1 IN DIG-2 IN DIG-2 IN DIG.OUT DIG.OUT OPT OPT DIG-4 IN DIG-4 IN DIG-3 IN DIG-3 IN DIG.OUT DIG.OUT COAX COAX SURROUND SURROUND BACK BACK R R SURROUND SURROUND L L L L FRONT FRONT CENTER CENTER R R
VIDEO VIDEO S-VIDEO S-VIDEO
IN IN OUT OUT IN IN OUT OUT IN IN OUT OUT IN IN IN IN IN IN OUT OUT
DSS DSS // VCR2 VCR2 VCR1 VCR1 DVD DVD
AUDIO AUDIO
TV TV TAPE TAPE CD CD CDR CDR // MD MD SUB SUB WOOFER WOOFER CENTER CENTER CENTER CENTER
FRONT FRONT FRONT FRONT SURROUND SURROUND SURR. SURR. BACK BACK SURROUND SURROUND SUB SUB WOOFER WOOFER SURR. SURR. BACK BACK
6.1CH INPUT 6.1CH INPUT
L L
R R
IN IN
MONITOR MONITOR OUT OUT VCR1 OUT VCR1 OUT VCR1 IN VCR1 IN DVD IN DVD IN
L L
R R
IN IN IN IN OUT OUT OUT OUT
PRE OUT PRE OUT
OUT OUT
MONITOR MONITOR
IN IN
TV TV DSS DSS // VCR2 VCR2 DVD DVD VCR1 VCR1
IN IN
GND GND
AM AM
FM FM
ANTENNA ANTENNA
((75 75 Ω Ω ))
REMOTE REMOTE
CONTROL CONTROL
MODEL NO. SR4300
SWITCHED 100W MAX SWITCHED 100W MAX
SPEAKER SYSTEMS SPEAKER SYSTEMS AC OUTLET AC OUTLET DIGITAL DIGITAL
DIG-1 IN DIG-1 IN DIG.OUT DIG.OUT OPT OPT DIG-4 IN DIG-4 IN
IN IN OUT OUT IN IN OUT OUT IN IN
AUDIO AUDIO
TAPE TAPE CD CD CDR CDR // MD MD
L L
R R
OUT IN
L
R
L
R
OUT
L
R
L R L R L R
R L L R R L
OUT IN
L
R
L
R
DIGITAL
OUTPUT
DIGITAL
OUTPUT
DIGITAL
INPUT
R L
L R L R
R L
L
R
CONNECTING AUDIO COMPONENTS
The output audio signal from the TAPE OUT jack and the CD-R/MD
OUT jack is the sound source currently selected.
Caution:
• Do not connect this unit and other components to mains power
until all connections between components have been
completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels properly.
Red connectors are for the R(right) channel, and white
connectors are for the L(left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is connected
with this unit.
• Do not bind audio/video connection cables with power cords
and speaker cables will result in generating hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are four digital inputs, two coaxial jacks and two optical jacks,
on the rear panel. You can use these jacks to input PCM, Dolby
Digital and DTS bitstream signals from a CD, DVD, or other digital
source components.
• There are one digital output with coaxial jack and one with optical
jack on the rear panel. These jacks can be connected to CD
recorder, MD deck.
• Setup the digital audio format of DVD player, or other digital source
component. Refer to the instructions for each component to be
connected to digital input jacks.
• Use fiber optical cables(optical) for DIG-1,2 input jacks. Use 75
ohms coaxial cables(for digital audio or video) for DIG-3,4 input
jacks.
• You can designate the input for each digital input/output jacks
according to your component. See page 19.
Notes:
• There is no Dolby Digital RF input jack. Please use an external
RF demodulator Dolby Digital decoder when connecting the
Dolby Digital RF output jack of the video disc player to the
digital input jack.
• The digital signal jacks on this unit conform to the EIA
standard. If you use a cable that does not conform to this
standard, this unit may not function properly.
• Each type of audio jack works independently. Signals input
through the digital and analog jacks are output through the
corresponding digital and analog jacks, respectively.
CD RECORDER / MD DECK
CD PLAYER
TAPE DECK
ANALOG AUDIO
DIGITAL AUDIO
(COAXIAL)
DIGITAL AUDIO
(OPTICAL)