Marantz SR5003 - Manual (Page 38)

ENGLISH
35
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
SETUP
3 SURROUND SETUP
This menu is for setting surround effect parameters
for the various surround input signals so as to bring
out the live audio effect of your speaker system.
• CHANNEL LEVEL:
“3-1 CHANNEL LEVEL” (see page 35)
• PLIIx MUSIC PARAMETER:
“3-2
PLIIx MUSIC PARAMETER” (see page 36)
• CSII PARAMETER:
“3-3
CSII PARAMETER” (see page 36)
• NEO:6 PARAMETER:
“3-4 NEO:6 PARAMETER” (see page 36)
1. Select “3. SURR SETUP” from the MAIN
MENU with the 3 or 4 cursor buttons and press
the ENTER button.
2. Select the desired menu with the 3 or 4 cursor
buttons and press the ENTER button.
3 . S U R R S E T U P
C H A N N E L L E V E L
P L x M U S I C P A R A M E T E R
C S P A R A M E T E R
N E O : 6 P A R A M E T E R
H T - E Q : O F F
L F E L E V E L : 0 d B
M - D A X : O F F
R E T U R N N E X T E X I T
HT-EQ:
Select to active the HT-EQ with the 1 or 2 cursor
buttons.
The total balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is because
fi lm soundtracks were designed to be played back
in large movie theater environments.
Activating the HT-EQ feature when watching a fi lm
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE DIRECT
• When VIRTUAL is set for the surround mode
LFE LEVEL:
Select the output level of the LFE signal included in
the Dolby Digital signal or the DTS signal.
Select “0dB”, “–10 dB” or “OFF” with the
1 or 2
cursor button.
M-DAX:
Select the desired M-DAX mode.
Select “HIGH”, “LOW” or “OFF” with the
1 or 2
cursor button. (See page 44)
3 . S U R R S E T U P
C H A N N E L L E V E L
P L x M U S I C P A R A M E T E R
C S P A R A M E T E R
N E O : 6 P A R A M E T E R
H T - E Q : O F F
L F E L E V E L : 0 d B
M - D A X : O F F
R E T U R N N E X T E X I T
C H A N N E L L E V E L
S U R R . M O D E :
A U T O
C E N T E R : 0 . 0 d B
S U R R . R : 0 . 0 d B
S U R R . B R : 0 . 0 d B
S U R R . B L : 0 . 0 d B
S U R R . L : 0 . 0 d B
S U B W : 0 . 0 d B
R E T U R N
E X I T
N E O : 6 P A R A M E T E R
C E N T E R G A I N :
0 . 3
R E T U R N
N E X T E X I T
P L x M U S I C P A R A M E T E R
P A R A M E T E R :
D E F A U L T
P A N O R A M A : O F F
D I M E N S I O N : 0
C E N T E R W I D T H : 3
R E T U R N
N E X T E X I T
C S P A R A M E T E R
T R U B A S S :
0
S R S D I A L O G : 0
R E T U R N
N E X T E X I T
☞
P. 36
☞
P. 35
☞
P. 36
☞
P. 36
3-1 CHANNEL LEVEL
1. Select “3. SURR SETUP” from MAIN MENU
with 3 or 4 cursor buttons and press the
ENTER button.
2. Select “CHANNEL LEVEL” with the 3 or 4
cursor buttons and press the ENTER button.
3. Set the SURR. MODE with the 1 or 2 cursor
buttons.
C H A N N E L L E V E L
S U R R . M O D E :
A U T O
C E N T E R : 0 . 0 d B
S U R R . L : 0 . 0 d B
S U R R . R : 0 . 0 d B
S U R R . B A C K L : 0 . 0 d B
S U R R . B A C K R : 0 . 0 d B
S U B W : 0 . 0 d B
R E T U R N E X I T
4. Select the desired menu item with the 3 or 4
cursor buttons, set the desired level with the
1 or 2 cursor buttons, and press the ENTER
button.
SURROUND MODE:
The surround mode can be independently set for
3 modes.
1. Multi Ch STEREO
2. CSII
3. Others
CHANNEL LEVEL
CENTER LEVEL:
Set the effect level of the center speaker between
–12 and +12 level in 0.5 level interval .
• If “NO” was selected for the center speaker setting
in the SPEAKER SIZE, then this setting will not
appear.
SURR L or R LEVEL:
Set the effect level of the Surround speaker
between –12 and +12 level in 0.5 level interval .
• If “NO” was selected for the surround speakers
setting in the SPEAKER SIZE, then this setting will
not appear.
SURR. BACK L or R LEVEL:
Set the effect level of the Surround Back speaker
between –12 and +12 level in 0.5 level interval .
• If “NO” was selected for the surround back speakers
setting in the SPEAKER SIZE, then this setting will
not appear.
After you complete this portion of the setup, move
the cursor to “RETURN” with the
3, 4, 1, 2 cursor
buttons and press the ENTER button.