Marantz SR5003 - Manual (Page 70)

67
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
TROUBLESHOOTING
HDMI
SYMPTOM CAUSE REMEDY
The display does not
appear over an HDMI
connection. The connected monitor or projector
does not support HDCP. Be sure to use an HDCP-compatible
monitor or projector.
The HDMI input of on the TV is
not on. Set HDMI input so that it turns on, as
explained in the TV's instruction manual.
The HDMI output on the source
component (DVD, Set Top Box,
etc.) is not on. Set HDMI output so that it turns on, as
explained in the source component's
instruction manual.
The HDMI mode is not correctly
set on the unit. Set HDMI input on the FUNC INPUT
SETUP menu as explained on page 27.
The HDMI output video resolution
of the source component (DVD,
Set Top Box, etc.) does not match
the TV specifi cations. Set the resolution so that it matches, as
explained in the instruction manuals of both
components.
The device is connected with a
non-standard HDMI cable. A 5 m or shorter cable is recommended to
ensure stable operation and prevent image
quality deterioration.
Power to the unit is off. (When
the unit is on standby, HDMI
connections cannot be turned
on.) Turn on the power to the unit.
T h e c o n n e c t i o n b e t w e e n
HDMI components was not
authenticated. Shut off and then turn the power back on to
the unit, TV and source component.
The HDMI OUT RES setting does
not match that of the connected
TV. Set the HDMI OUT RES setting to AUTO.
(See page 37.)
Time is needed for the
d i s p l ay o f a n H D M I
connection to appear. T h e c o n n e c t i o n i s b e i n g
authenticated between the HDMI
devices. There is nothing wrong with the system.
Some HDMI devices require time for
authentication.
Au d i o i s n o t p l aye d
b a ck ove r a n H D M I
connection. The HDMI audio output of the
source component (DVD, Set Top
Box, etc.) is not on. Set the HDMI audio output so that it turns
on, as explained in the source component's
instruction manual.
The signal format of the source
component (DVD, Set Top Box,
etc.) is not supported by the unit. Set the HDMI audio output so that it can
connect to the unit, as explained in the
source component's instruction manual.
This unit is set to the HDMI audio
“THROUGH” mode. In the “THROUGH” mode, sound is not
produced from the unit. Set it to “ENABLE”.
(see page 38)
DVD-Audio is not played
b a ck ove r a n H D M I
connection. The DVD player does not support
CPPM, therefore it cannot output
HDMI audio. • Use a DVD-Audio player that supports
CPPM.
• Turn on PCM downsampling on the DVD
player.
• Use an analog connection.
XM SATELLITE RADIO
If a problem should arise, fi rst check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properIy?
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there
may be a malfunction. Disconnect the power immediately and contact your store of purchase.
SYMPTOM CAUSE REMEDY
“TUNER” is displayed. The XM Mini-Tuner and this unit are not
properly connected. Check that the units are properly
connected.
“ANTENNA” is displayed. The XM antenna is not properly connected
to the Mini-Tuner Dock. Check that the antenna is properly
connected. Also, check the antenna cable
for damage.
“NO SIGNAL” is displayed. The Signal cannot be received. Reposition your XM antenna.
Receiving only channels 0 and 1. The XM Mini-Tuner is not activated. Contact XM Satellite Radio.
(See page 49)
“UPGRADE TUNER” is displayed. The connected XM CNP-1000 is
incompatible. Upgrade the XM CNP-1000 to the XM
Mini-Tuner.
Report the model of the AV receiver and
the ID number of the CNP-1000 to XM
Listener Care. (See page 49.)
SIRIUS SATELLITE RADIO
SYMPTOM CAUSE REMEDY
“TUNER ERR” is displayed. SiriusConnect TM tuner is not properly
connected.
Check the 8pin mini DIN cable and AC
adapter connection are correct.
“ANTENNA” is displayed Antenna is not properly connected. Check the antenna cable connection is
correct.
“ACQUIRING” is displayed. The signal cannot be received. Reposition your SiriusConnect TM tuner
and antenna.
“CALL SIRIUS” is displayed You have not subscribed for the selected
channel. Call SIRIUS if you want to subscribe.
(See page 54)
“FIRM UPDT” is displayed SiriusConnect TM is updating software. Wait until the updating is complete.