Specifications – MITSUBISHI ELECTRIC DX-TL4516U User Manual
Page 130
127
Specifications
Rated Power Supply .................100 to 240 V AC, 50/60 Hz
Rated Input ...............................0.9- 0.4 A (100-240 V)
Colour System ..........................NTSC-type colour system.
Operating Temperature .............41 °F-104 °F (5 °C to 40 °C)
Relative Humidity .....................Max. 80 (%)
Altitude .....................................Max. 2000 (m)
Dimensions ...............................425 (Width) x 375 (Depth) x 133 (Height) (mm)
Weigh .....................................9.1 kg
Recording System ....................Digital recording system
Sampling ............................13.5 MHz
Data Compression .............JPEG2000
Compression Unit ...............Frame, Field
Recording Resolution ...............720 x 480, 720 X 240
Recording Device .....................Hard disk drive (HDD)
Video Input ...............................16 Input BNC-Connectors: 1.0 V(p-p), 75 ohms.
Monitor Output ..........................S-Connector: Y-Signal:
1.0 V(p-p), 75 ohms.
C-Signal:
0.286 V(p-p), 75 ohms.
2 Output BNC-Connectors: 1.0 V(p-p), 75 ohms.
RCA-jack:
1.0 V(p-p), 75 ohms.
Throughout Output ..................16 Output BNC-Connectors: 1.0 V(p-p), 75 ohms.
Audio Input ...............................RCA-Jack:
308 mV(rms), 50 k ohms.
Audio Output ............................RCA-Jack:
308 mV(rms), 1 k ohms.
Clock .....................................±20 seconds/month (when power is supplied, 25 °C)
Timer Program ..........................8 programs-Daily start and stop time for one week x 2 set
Memory Backup .......................Lasts for more than 1 month (when fully charged)
Connectors
External storage terminal ...Serial bus (1-4) (For connecting the recommended optional items only)
Control terminals
Clock adjust Input ........Active:
When terminals are short-circuited or “Low” Level voltage is applied.
Non active:
Open.
Clock adjust Output ......Active:
“Low” Level Max. Drive current 30 mA DC.
Non active:
Open.
Max. Voltage 24 V DC.
(Clock adjust Output is throughout of Clock adjust Input)
Recording start Input ....Active:
When terminals are short-circuited or “Low” Level voltage is applied.
Non active:
Open.
Recording stop Input ....Active:
When terminals are short-circuited or “Low” Level voltage is applied.
Non active:
Open.
Emergency Input ..........Active:
When terminals are short-circuited or “Low” Level voltage is applied.
Non active:
Open.
Mode out (1-4) .............Active:
“Low” Level Max. Drive current 30 mA DC.
Non active:
Open.
Max. Voltage 24 V DC.
Call out +/– ...................Active:
Short
Max. Drive current 7 mA DC.
(Photo coupler output) Non active:
Open.
Max. Voltage 24 V DC.
Ground terminal
DC 12 V Output ............Max. 350 mA DC (when Main switch and power button is turned on)
Alarm Input (1-16) ........Active:
When terminals are short-circuited or “Low” Level voltage is applied.
Non active:
Open.
Alarm Output (1-16) .....Active:
“Low” Level Max. Drive current 30 mA DC.
Non active:
Open.
Max. Voltage 24 V DC.
PTZ terminal ................RS-232C terminal
RS-422 terminal
Serial port .....................RS-232C D-SUB 9 pin
RS-485 port ..................RS-485 Input/Output, RJ-11
Communication
LAN ..............................Connector form: RJ-45 Physical interface: 10BASE-T/100BASE-TX
DVD-R/RW, CD-R/RW recording format ...........Original format
Accessories ..............................AC power cord
1
CD
1
Cable clamping band
2
Installer’s manual (this manual)
1
User’s manual
1
Weight and dimensions shown are approximate.
Design and specifications are subject to change without notice.
Specifications