Marantz SR3001 - Manual (Page 15)

12
ENGLISH
Caution:
• Be sure to use speakers with the specifi ed impedance as
shown on the rear panel of this unit.
• To prevent damage to circuitry, do not let the bare
speaker wires touch each other and do not let them
touch any metal part of this unit.
• Do not touch the speaker terminals when the power is on.
It may cause you to receive an electric shocks.
• Do not connect more than one speaker cable to one
speaker terminal. Doing so may damage this unit.
Note:
Be sure to connect the positive and negative cables for
the speaker properly. If they are miss-connected, the
signal phase will be reversed and the signal quality
will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect a
powered subwoofer (power amplifi er built in ).
If your subwoofer is a passive type (power amplifi er
is not built in), connect a monaural power amplifi er to
the PRE OUT SUBWOOFER jack and connect the
subwoofer to the amplifi er.
CONNECTING AUDIO COMPONENTS
IN OUT MONITOR VCR1
MONITOR
R
SPEAKER SYSTEMS 6 - 8 OHMS
CENTER
R
FRONT SURROUND BACK S. SPEAKER B SURROUND
L L L R
DVD OUT IN MONITOR TV DVD VCR1 OUT IN DSS / VCR2 OUT
VIDEO
IN Y
DSS / VCR 2 DVD 3 2 1 7.1CH INPUT
L SL C SBL
SBR SW SR R TV DVD VCR1 OUT IN IN OUT DSS / VCR2 IN OUT CDR/MD TAPE OUT IN CD
R
L
FM (75 Ω) GND AM
CB / PB
CR / PR
ANTENNA
RC-5
DIGITAL INPUT COMPONENT VIDEO AUDIO
AC IN S-
VIDEO
OUT SUBWOOFER
MODEL NO. SR3001 MODEL NO. SR3001
3 1 IN OUT CDR/MD TAPE OUT IN CD
R
L
OUT IN
L
R
L
R
OUT
L
R
L R L R L R
R L R L R L
OUT IN
L
R
L
R
DIGITAL
OUTPUT
DIGITAL
OUTPUT
R L
R L R L
R L
L
R
The output audio signal from the TAPE OUT jack and
the CD-R/MD OUT jack is the same signal which is
currently selected.
Caution:
Do not connect this unit and other components to mains
power until all connections between components have
been completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is
connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 3 digital inputs, 2 coaxial jacks and
1 optical jack, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other digital
source components.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fi ber optical cables (optical) for DIG-1 input
jacks. Use 75 ohms coaxial cables (for digital audio
or video) for DIG-2, 3 input jacks.
• You can designate the input for each digital input
jacks according to your component. See page 17.
CD recorder / MD deck
CD player
Tape Deck
Analog Audio
Digital Audio (coaxial)
Digital Audio (optical)
Notes:
• There is no Dolby Digital RF input jack. Please use
an external RF demodulator Dolby Digital decoder
when connecting the Dolby Digital RF output jack
of the video disc player to the digital input jack.
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does not
conform to this standard, this unit may not function
properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks are
output through the corresponding digital and analog
jacks, respectively.