Marantz SR3001 - Manual (Page 26)

23
ENGLISH
USING THE SLEEP TIMER
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD VCR1 DSS/VCR2 TV
ENTER
AUX1
To program the SR3001 for automatic standby, press
the SLEEP button on the remote.
Each press of the button will increase the time before
shut down in the following sequence.
OFF 10 20 30 40
90 80 70 60 50
The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP button
until the display shows “SLEEP OFF” and the SLEEP
indicator will disappear.
NIGHT MODE
TUNE/SEARCH TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
MENU OSD
ENTER
Press the NIGHT button on the remote to turn on the
NIGHT mode.
Selecting the Night Mode ON is effective in Dolby
Digital only, and it compresses the dynamic range.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late
at night.
To turn off the Night mode, press the NIGHT button
again.
BASIC OPERATION
(PLAY BACK)
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must
fi rst select the input source on the SR3001.
Example : DVD
SURROUND
AV SURROUND RECEIVER SR3001
INPUT SELECTOR
PHONES
STANDBY
7.1CH INPUT PURE SETUP DIRECT SIMPLE
AUTO HT-EQ MENU
MODE
DISP MULTI AUTO TUNED ST V – SLEEP SURR AUTO DIRECT DISC 6.1
POWER ON/OFF
S. SPEAKER B
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
AUX1
To select DVD, turn the INPUT FUNCTION
SELECTOR knob on the front panel or simply press
the DVD button on the remote.
After you have selected DVD, simply turn on the DVD
player and play the DVD.
• The input name will appear in the display on the front
panel.
• As the input is changed, the SR3001 will
automatically switch to the digital input, surround
mode, attenuation, and night mode status which
were entered during the confi guration process for
that source.
• When an audio source is selected, the last video
input used remains routed to the VCR1 & DSS/
VCR2 Outputs and Monitor Outputs. This permits
simultaneous viewing and listening to different
sources.
• When a Video source is selected, the video signal
for that input will be routed to the Monitor Outputs
jacks and will be viewable on a TV monitor
connected to the SR3001.
If a component video input is connected to the
DVD or DSS component inputs, it will be routed
to the Component Video Output. Make certain
that your TV is set to the proper input to view the
signal.
SELECTING THE SURROUND MODE
Example : AUTO SURROUND
SURROUND
AV SURROUND RECEIVER SR3001
INPUT SELECTOR
PHONES
STANDBY
7.1CH INPUT PURE SETUP DIRECT SIMPLE
AUTO HT-EQ MENU
MODE
DISP MULTI AUTO TUNED SLEEP SURR AUTO DIRECT
POWER ON/OFF
S. SPEAKER B
TUNE/SEARCH TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
ENTER
To select the surround mode during playback, press
the SURROUND MODE button on the front panel or
the Surround mode buttons on the remote.
ADJUSTING THE MAIN VOLUME
DOWN UP
VOLUME
MUTE ATT DISPLAY MEMORY CLEAR
T-MODE EXIT BAND
AK ANALOG DIGITAL ATT EQ DIGITAL SURROUND
AAC PCM L C R SL S SR LFE
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD VCR1 DSS/VCR2 TV
ENTER
AUX1
Adjust the volume to a comfortable level using the
VOLUME control knob on the front panel or VOL
3 /
4 buttons on the remote.
To increase the volume, turn the VOLUME knob
clockwise or press VOL
3 button on the remote, to
decrease the volume, turn counterclockwise or press
VOL
4 button on the remote.
Notes:
• The volume can be adjusted within the range of – ∞ to
18 dB, in steps of 1 dB.
• However, when the channel level is set as described
on page 20, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to 18
dB.
(In this case the maximum volume adjustment range
is “18 dB - Maximum value of channel level)
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
CH.SEL LIP.SYNC
PTY SUB-T/ATT AUDIO INPUT/DISC+
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote control unit)
To adjust the bass effect, press BASS
3 or BASS4
on the remote.
To adjust the treble effect, press TREBLE
3 or
TREBLE 4 on the remote.
Note:
The tone control function can work in the AUTO
Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and
Multi Ch. Stereo mode.
TEMPORARILY TURNING OFF THE SOUND
DOWN UP
VOLUME
MUTE ATT DISPLAY MEMORY CLEAR
T-MODE EXIT BAND
ANALOG DIGITAL DIGITAL SURROUND
AAC PCM L C R SL S SR LFE
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD VCR1 DSS/VCR2 TV
ENTER
AUX1
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the front panel or MUTE button on the
remote.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
“MUTE” .
Press the MUTE button again to return to normal
operation.