Integra DTR-5.2 - Manual (Page 25)

25
Enjoying music or videos with the DTR-5.2
Basic operation
To use the remote controller, first press the RCVR button.
1. Press the desired input source button.
The selected source name appears on the display. If you have
selected DVD, CD, or other digital devices, see “Digital Input”
on page 29. If you have selected a multichannel input, see
“Multichannel” on page 29 and “Enjoying the multichannel
input” on page 27.
2. Make sure that the Speakers A
indicator is lit on the display. If it is
not lit, press the Speakers A button.
(Refer to the “Selecting speakers” section on page 26 for more
details.)
3. Start playing the selected input source.
Follow the operating instructions for the source device.
4. Selecting a listening mode.
Select a listening mode. (Refer to this page.)
5. Adjust the volume to an appropriate level.
These controls allow you to adjust the volume of the Front,
Center, Surround speakers and subwoofer simultaneously.
Turning the control clockwise increases the volume level.
Turning the control counterclockwise decreases the volume.
(Refer to page 26 for more information.)
Master Volume
A Speakers
Selecting a listening mode
Select your desired listening mode using the jog dial.
• Depending on the software that you are playing, SURROUND
will be Dolby Digital, DTS, or Dolby Pro Logic II.
• Refer to page 28 for more details of listening modes.
• Refer to page 30 for sources and listening modes.
• When playing Dolby Digital or DTS software, the listening
mode will automatically change to Dolby Digital or DTS.
• With Dolby Digital and Dolby Pro Logic II Movie, you can use
the Re-EQ function (for more details, see page 9).
Tip:
You can set in advance a different listening mode for each input
source. For more details, see page 29.
When turning the jog dial
The items change as shown below:
DIRECT
↔ STEREO ↔ SURROUND ↔
ORCHESTRA ↔ UNPLUGGED ↔
STUDIO MIX
↔ TV LOGIC ↔ ALL CH
STEREO
↔ DIRECT...
When pressing the jog dial
Each time you press it, the items change as
shown below:
DIRECT
→ STEREO → SURROUND →
ALL CH STEREO
→ DIRECT...
Note:
If you want to switch between Dolby Pro Logic II Movie and Dolby
Pro Logic II Music at the DTR-5.2, press the jog dial and select
“SURROUND” for the listening mode.
When using the remote controller (for more details, see
page 9)
1. Press the RCVR MODE button.
2. Press one of the listening mode buttons, STEREO,
DIRECT, A. ST, SURR, DSP , or DSP , to select the
listening mode.
Push To Enter
DSP / Mode ADJ
Push To Enter
DSP / Mode ADJ
Standby/On
Standby
Power
On O f f
Phones DVD Video 2 Video 1 Video 3
Bass Treble
Master Volume
Smart Scan Navigator Dimmer Display Tuning FM Mode Preset Memory Preset
VCR
Audio Selector Tape FM AM Phono CD
Push To Enter
DSP/ Mode ADJ Setup
Return
CH Level A B Speakers
HOME THEATER CONTROLLER RC-441M
Master Volume
RCVR
MODE
SP A
MUTING
Re-EQ
Speakers A/B
Display
Treble Bass
DISPLAY
VOL
Jog dial
Input source buttons
FM AM Phono C D Tape
VCR
DVD Video 3 Video 2 Video 1
DTR-5.2
Remote controller
SP A
7
Listening mode
buttons
• Use the bass and treble controls to adjust the tone.
(Refer to page 26 for more information.)
DTR-5.2 Remote controller