Integra DTR-5.2 - Manual (Page 27)

27
Enjoying the multichannel input
Before starting operations, first make sure that the multichannel
connection is properly made and that the Multichannel setting of the
Input Setup
→ Audio Setup is set to “YES” (see page 29).
1. Press the input source button for the component with
multichannel output connected to the MULTI
CHANNEL INPUT on the rear of the DTR-5.2.
2. Select “MULTICH” using the Audio Selector button
on the front panel (AUDIO button on the remote
controller).
Changing the audio mode
Press the Audio Selector button on the front panel (or the AUDIO
button on the remote controller) to change the audio mode. Each
time the button is pressed, the mode changes from “AUTO”
→
“MULTICH” → “ANALOG” and back to “AUTO.” The “AUTO”
audio mode is recommended for normal circumstances.
AUTO (automatic detection): With this setting, the DTR-5.2
automatically detects whether the input signal is digital or analog.
When a digital signal is not input, then the analog signal is played.
MULTICH: Select this setting to play back the input from the
component connected to the MULTI CHANNEL INPUT port. This
setting is effective when the Multichannel setting in the Audio Setup
is set to “YES.”
ANALOG: Select this setting to play back the input from a source
component connected to an analog audio input jacks. With this
setting, even if a digital signal is input from the same component,
only the analog signal will be output.
Audio
Selector
DTR-5.2 Remote controller
Using the tone control:
To make the Bass and Treble dials work for multichannel sources,
you must first set the tone control to “ON.”
1. Turn the tone control on by pressing either the jog
dial on the DTR-5.2 or the DIRECT button on the
remote controller.
When pressed only once, the current setting appears, so press
twice to change the setting.
2. Adjust the tone using the Bass and Treble dials.
Bass Treble
DIRECT
2
Push To Enter
DSP / Mode ADJ
When using the remote controller:
1. Press the RCVR MODE button.
2. Press the CH SEL button and select
the desired speaker.
3. Press the LEVEL or button to
adjust the volume level.
Notes:
• You cannot select a speaker if the CONFIG parameter of the
speaker is set to NO or NONE.
• If the speaker level is set to +1 dB or higher, the maximum level
indicated on the display will change if you raise the volume
level.
• When you press the TEST button after you set the level, the
current level will be used as the value set via the test tone.
Notes:
• Adjusting the volume level of each speaker for the MULTI CH
INPUT source does not affect the speaker level adjusted by the
listening position.
• If the speaker level is set to +1 dB or higher, the maximum level
indicated on the display will change if you raise the volume
level.
3. Turn on the connected component and start playing
the desired media.
4. If necessary, adjust the output level of each speaker
as desired (see “Temporarily changing the speaker
output levels” on this page).
Adjust the speaker output levels so that you can hear the same
sound level from each speaker at the listening position. For the
front right, front left, center, surround right, and surround left
speakers, the output levels can be adjusted between –12 to +12
decibels. The subwoofer can be adjusted between –30 to +12
decibels.
5. Adjust the volume with the Master Volume dial or the
VOL buttons on the remote controller.
Enjoying music or videos with the DTR-5.2
Temporarily changing the speaker output levels
To change the individual speaker volumes temporarily, follow the
procedure given below. Each channel can be set between –12 to +12
decibels. Note that the calibration settings will return to the original
settings when the DTR-5.2 is put in standby.
1. Press the CH Level button and select
the desired speaker.
2. Turn the jog dial to adjust the
volume level.
CH Level
Push To Enter
DSP / Mode ADJ