Icom IC-F3061S - Manual (Page 13)

SECTION 6 ADJUSTMENT PROCEDURES
▄ REQUIRED TEST EQUIPMENT
EQUIPMENT GRADE AND RANGE EQUIPMENT GRADE AND RANGE
FM deviation meter
Frequency range
Measuring range : DC–300 MHz
: 0 to
±10 kHz
Attenuator
Power attenuation
Capacity : 20 or 30 dB
: 10 W
Frequency counter
Frequency range
Frequency accuracy
Sensitivity : 0.1–300 MHz
: ±1 ppm or better
: 100 mV or better
Standard signal
generator (SSG) Frequency range
Output level
: 0.1–300 MHz
: 0.1 µV to 32 mV
(–127 to –17 dBm)
RF power meter
Measuring range
Frequency range
Impedance
SWR : 1–10 W
: 100–300 MHz
: 50
Ω
: Better than 1.2 : 1
Oscilloscope
Frequency rang
Measuring range : DC–20 MHz
: 0.01–20 V
External speaker
Input impedance
Capacity : 8 Ω
: 1 W or more
6 - 1
6-1 PREPARATION
When adjusting IC-F3060 series, the optional CS-F3060 ADJ ADJUSTMENT SOFTWARE (Rev. 1.1 or later), OPC-966 JIG CABLE
(modifi ed OPC-966 CLONING CABLE ; see illustration page 5-2) and below test equipments are required.
▄ SYSTEM REQUIREMENTS
• Microsoft
®
Windows
®
98/98SE/Me/2000/XP
• RS-232C serial port (D-sub 9 pin)
▄ ADJUSTMENYT SOFTWARE INSTALLATION
q Quit all applications when Windows is running.
w Insert the CD into the appropriate CD drive.
e Double-click the “Setup.exe” contained in the ‘CS-F3060
ADJ’ folder in the CD drive.
r The “Welcome to the InstallShield Wizard for CS-F3060
ADJ” will appear. Click [Next>].
t The “Choose Destination Location” will appear. Then click
[Next>] to install the software to the destination folder. (e.g.
C:\Program Files\Icom\CS-F3060 ADJ)
y After the installation is completed, the “InstallShield Wiz-
ard Complete” will appear. Then click [Finish].
u Eject the CD.
i Program group ‘CS-F3060 ADJ’ appears in the ‘Programs’
folder of the start menu, and ‘CS-F3060 ADJ’ icon ap-
pears on the desk top screen.
▄ BEFORE STARTING SOFTWARE ADJUSTMENT
Clone the adjustment frequencies into the transceiver, and
set the confi guration using with the CS-F3060
CLONING SOFT-
WARE before starting the software adjustment. Otherwise, the
software adjustment can not be started.
CAUTION!: BACK UP the originally programmed mem-
ory data in the transceiver before program-
ming the adjustment frequencies.
When program the adjustment frequencies into
the transceiver, the transceiver’s memory data
will be overwritten and lose original memory
data at the same time.
Microsoft and Windows are registered trademarks of Micro-
soft Corporation in the U.S.A. and other countries.
▄ STARTING SOFTWARE ADJUSTMENT
q Connect the transceiver and PC with OPC-966
JIG CABLE .
w Turn the transceiver power ON.
e Boot up Windows, and click the program group ‘CS-F3060
ADJ’ in the ‘Programs’ folder of the [Start] menu, then
CS-F3060 series ADJ’s window appears.
r Click ‘Connect’ on the CS-F3060 ADJ’s window, then
appears transceiver’s up-to-date condition.
t Set or modify adjustment data as specifi ed.
• ADJUSTMENT FREQUENCY LIST
CH FREQUENCY ADJUSTMENT ITEM
1 174.000 MHz
TX power
Mode : Low1
: Narrow
2 154.900 MHz
TX power
Mode : Low1
: Narrow
3 155.000 MHz
TX power
Mode : High
: Wide
4 155.000 MHz
TX power
Mode : Low2
: Wide
5 155.000 MHz
TX power
Mode : Low1
: Wide
6 136.000 MHz
TX power
Mode : Low1
: Wide
7 174.000 MHz
TX power
Mode : Low1
: Wide
8 136.000 MHz
TX power
Mode : Low1
: Narrow
9* 155.000 MHz
TX power
Mode : Low1
: Digital
10* 136.000 MHz
TX power
Mode : Low1
: Digital
11* 174.000 MHz
TX power
Mode : Low1
: Digital
12 155.000 MHz
TX power
Mode
CTCSS : Low1
: Wide
: 151.4 Hz
13 155.000 MHz
TX power
Mode : Low1
: Narrow
14
†
155.000 MHz
TX power
Mode : Low1
: Middle
15 † 136.000 MHz
TX power
Mode : Low1
: Middle
16 † 174.000 MHz
TX power
Mode : Low1
: Middle
*; Necessary only when the optional UT-119 is installed.
†
; [EUR-01] only