JVC RX-884RBK - Manual (Page 68)

63
English
IMPORTANT:
To operate JVC’s audio components using this remote control:
•
You need to connect JVC audio components through the COMPU LINK-3
(SYNCHRO) jacks (see page 55) in addition to the connections using cables
with RCA pin plugs (see page 9) or using digital cables (see page 12).
• Aim the remote control directly at the remote sensor on the receiver.
Tuner
After pressing FM/AM (with the remote control mode selector
set to “AUDIO/TV/VCR”), you can perform the following
operations:
FM/AM:
Alternates between FM and AM (MW/
LW).
1 – 10, +10: Selects a preset channel number directly.
For channel number 5, press 5. For
channel number 15, press +10, then 5.
For channel number 20, press +10, then
10.
PTY SEARCH: Searches for a program by PTY codes.
PTY +/–: Selects the PTY codes.
DISPLAY MODE: Shows the RDS signals.
FM MODE/MUTE: Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations (with the
remote control mode selector set to “AUDIO/TV/VCR”):
SURROUND MODE: Changes the DSP modes.
After pressing SOUND CONTROL (with the remote control
mode selector set to “AUDIO/TV/VCR”), you can perform the
following operations:
SEA MODE:
Changes the SEA modes.
SUBWOOFER +/–: Adjusts the subwoofer output level.
CNTR +/–: Adjusts the center speaker output
level.
REAR•L +/–: Adjusts the left rear speaker output
level.
REAR•R +/–: Adjusts the right rear speaker output level.
EFFECT: Selects the effect level.
TEST: Turns on or off the test tone output.
CNTR TONE: Selects the center tone.
CD player
After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR”),
you can perform the following operations on a CD player:
PLAY:
Starts playing.
4 4 4 4 4:
Returns to the beginning of the current (or previous) track.
¢ ¢ ¢ ¢ ¢: Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
1 – 10, +10: Selects a track number directly.
For track number 5, press 5. For track number 15, press +10, then 5. For
track number 20, press +10, then 10. For track number 30, press +10,
+10, then 10.
Notes:
• If you use the buttons on the
front panel or the menu
function to choose a source,
the remote control will not
operate that source. To
operate a source with the
remote control, the source
must be selected using
buttons on the remote control.
• Check to see if its remote
control mode selector is set to
the correct position. To
operate audio system, TVs,
and VCRs, set it to “AUDIO/
TV/VCR.”
• Refer also to the manuals
supplied with your
components.
Note:
After adjusting sounds, press
the corresponding source
selecting button or CD DISC to
operate your target source by
using 10 keys; otherwise, 10
keys cannot be used for
operating your target source.
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control
signals for JVC components are preset in the remote control.
RM-SR884RU REMOTE CONTROL
SOUND CONTROL
CD
DISC
VCR1 ANALOG /DIGITAL AUDIO
DVD VCR1 VIDEO VCR2
CD
TV/DBS
TEST
REAR R
REAR L
SEA MODE SUBWOOFER
TAPE/MD FM/AM PHONO
5 4 6
2 1 3
8 7 /P 9
0 +10 10
AUDIO/TV
/VCR
VCR1 TAPE
CONTROL
VOLUME
CHANNEL
MUTE
FF / ¢
PLAY
STOP
REC
TV/VIDEO
TV VOLUME
PAUSE
4 / REW
TV/CATV
CNTR CNTR TONE
ENTER
MENU
EFFECT
CATV
/DBS
FM MODE/MUTE 100+ RETURN
SURROUND
MODE
O N
SC REEN CON TR
O L
SET EXIT
PTY –
PTY +
PTY SEARCH
DISPLAY MODE
/DBS
EN63_76.RX-884R[E]/1.PM5 98.3.26, 1:10 PM 63