JVC RX-8012RSL - Manual (Page 15)

12
Notes:
• When connecting an MD recorder (to the TAPE/MD jacks), and a
DBS tuner (to the TV SOUND/DBS jacks), change the source
names shown on the display. For details, see page 16.
• When you press one of the source selecting buttons on the remote
control marked with an asterisk ( * ), the receiver automatically turns
on.
Signal and speaker indicators on the display
The signal indicators light up in the following cases:
• Only the indicators for the incoming signals light up.
• When analog input is selected, “L” and “R” always light up.
• When “DVD MULTI” is selected as the source, “L,” “C,” “R,”
“LFE,” “LS” and “RS” light up.
The speaker indicators light up only —:
The frames of “C,” “LS,” and “RS” light up, when the
corresponding speaker is set to “LARGE” or “SMALL”.
L : • When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
R : • When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
C : Lights up when the center channel signal comes in.
LS : Lights up when the left rear channel signal comes in.
RS : Lights up when the right rear channel signal comes in.
S : Lights up when the monaural rear channel signal comes in.
LFE : Lights up when the LFE channel signal comes in.
Note:
When “SUBWOOFER” is set to “YES,” SUBWFR lights up (see page
17).
Selecting different sources for picture and
sound
You can watch picture from a video component while listening to
sound from another component.
Press one of the audio source selecting buttons — PHONO, CD,
CDR, TAPE/MD, USB (AUDIO), FM/AM — while viewing the
picture from a video component such as the VCR or DVD player,
etc.
The lamp on the front panel button for selected source lights up.
DVD MUILTI DVD
USB
CD
CDR
TAPE/MD
TV/DBS VIDEO PHONO
FM/AM
VCR 1 VCR 2
TV SOUND/DBS VIDEO VCR 2 VCR 1 DVD DVD MULTI
FM / AM USB AUDIO TAPE / MD CDR CD PHONO
SOURCE NAME
SOURCE NAME
S S
C C
LS LS
L L
LFE LFE SUBWFR SUBWFR
RS RS
R R
S
C
LS
L
LFE SUBWFR SUBWFR
RS
R
Speaker indicators light up
in white: Signal indicators light up in
red:
MASTER VOLUME
+
−
VOLUME
On the front panel:
From the remote control:
Note:
Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
Adjusting the Volume
On the front panel:
To increase the volume, turn MASTER
VOLUME clockwise.
To decrease the volume, turn it
counterclockwise.
• When you turn MASTER VOLUME
rapidly, the volume level also changes
rapidly.
• When you turn MASTER VOLUME slowly,
the volume level also changes slowly.
From the remote control:
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
CAUTION:
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Notes:
• The volume level can be adjusted within the range of “0” (minimum)
to “90” (maximum).
• If you set One Touch Operation to “ON” (see page 22), you do not
have to adjust the volume level each time you change the source. It
is automatically set to the stored level.
EN11-27.RX-8010&8012R_f 01.3.19, 1:57 PM 12