JVC RX-8012RSL - Manual (Page 58)

55
To change the transmittable signals for
operating a CATV converter or DBS tuner
1. Press and hold CATV/DBS .
2. Press CATV/DBS CONTROL.
3 Enter manufacturer’s code using buttons 1–9,
and 0.
See the following lists to find the code.
4. Release CATV/DBS .
The following buttons can be used for the CATV converter and
DBS tuner:
CATV/DBS : Turns on and off the CATV converter
or DBS tuner.
CH +/–: Changes the channels.
1 – 10, 0, 100+ (+10): Selects the channels.
The 10 button will function as the
ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
Note:
Refer to the manual supplied with your CATV converter or DBS
tuner.
5. Try to operate your CATV converter or DBS
tuner by pressing CATV/DBS .
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct
one is entered.
Note:
You cannot use both of the CATV converter and DBS tuner at the
same time.
For DBS tuner
Manufacturer Codes
JVC 56, 57, 67
AMSTRAD 43, 44, 45, 46, 47, 48, 49
BLAUPUNKT 30
ECHOSTAR 50, 51, 67
GOLDSTAR 31
GRUNDIG 32, 33
HIRSHMANN 48, 52, 53, 54, 55
INSTRUMENT 68
ITT/NOKIA 34
KATHREIN 52, 58, 59, 60, 61, 62, 63
NEC 35, 36
ORBITECH 48
PHILIPS 37, 38
RCA 65
SAMSUNG 39, 40
SCHWAIGER 61, 64
SIEMENS 41, 42
SONY 66
TECHNISAT 48
Manufacturers’ codes are subject to change without notice. If
they are changed, this remote control cannot operate the
equipment.
To change the transmittable signals for
operating another manufacturer’s VCR
1. Press and hold VCR 1 .
2. Press VCR 1.
3. Enter manufacturer’s code using buttons 1–9,
and 0.
See the list on the next page to find the code.
4. Release VCR 1 .
The following button can be used for operating the VCR:
VCR 1 : Turns on and off the VCR.
After pressing VCR 1, you can perform the following operations
on the VCR:
CH +/–: Changes the TV channels on the
VCR.
1 – 10, 0, 100+ (+10): Selects the TV channels.
The 10 button will function as the
ENTER button if your VCR requires
pressing ENTER after selecting a
channel number.
3 PLAY: Starts playback.
REW: Rewinds a video tape.
FF: Fast winds a video tape.
7 STOP: Stops operation.
8 PAUSE: Pauses.
REC PAUSE : Enters recording pause.
Note:
Refer to the manual supplied with your VCR.
5. Try to operate your VCR by pressing VCR 1 .
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
For CATV converter
Manufacturer Codes
GENERAL INSTRUMENT 06, 07, 08, 09, 10, 11,
12, 13, 14, 29
HAMLIN/REGAL 01, 02, 03, 04, 05
JERROLD 06, 07, 08, 09, 10, 11,
12, 13, 14
OAK 15, 16, 17
PANASONIC 18, 19, 20
PIONEER 21, 22
SCIENTIFIC ATLANTA 23, 24, 25
TOCOM 26
ZENITH 27, 28
Manufacturers’ codes are subject to change without notice. If
they are changed, this remote control cannot operate the
equipment.
EN51_60.RX-8010&8012R_f 01.3.19, 2:00 PM 55