JVC XL-R5000BK - Manual (Page 28)

23
5
Select and enter the program source.
• The source can be selected in either direction using the MULTI
JOG dial on the main unit or the
4 and ¢ buttons on the
remote control.
• When the SET button is pressed, the programming and track
number flash.
6
Select and enter one of the tracks.
• After the track is entered, the amount of time remaining on the
CD-R or CD-RW appears in the display followed by the infor-
mation for the next step in the program.
7
Repeat steps 5 and 6 to continue programming
tracks.
• Up to 32 tracks can be programmed. The same track may be
programmed more than once.
• The Program Edit mode is stopped if 32 steps have been pro-
grammed or if there is no more time remaining on the CD-R or
CD-RW.
8
Press the CDR CONTROL 3 button to start
recording the program.
• Recording starts from the first step in the program, and stops
when the last step is finished.
• The program information is maintained in memory until one of
the disc trays (CD1, CD2, CD3) is opened.
When recording is complete
After “STOP DUBBING” is displayed, operation stops automati-
cally. It also stops automatically after the last step in the program is
finished.
To stop recording at any time
Press the 7 (stop) button.
The recording mode is released after “STOP DUBBING” is dis-
played.
Note
• If the source CD being recorded from the 3-CD changer is itself
a digital copy, digital recording cannot be performed. When this
occurs, the recording type will switch automatically from digital
to analog.
• The last program information (the most recently created pro-
gram still stored in the unit's memory) will be erased if the trays
of the 3-CD changer are opened and if listening Edit recording
is performed.
There are a number of advantages of having a 3-CD changer and
CDR in the same unit, mainly that the unit has direct control over
both components. Because of this, the following recording options
are available: high-speed (2x) recording and track spacing.
High-speed (2x) recording is only possible for digital recording
from the 3-CD changer to the CDR.
1
Press the CDR button on the remote control
while pointing at the unit to select the CDR
function.
2
When the unit is in the stop mode, press the
MENU button on the main unit (or the DISPLAY/
MENU button on the remote control while
holding down the SHIFT button)
3
Turn the MULTI JOG dial or press the 4 / ¢
button on the remote control until “DUB-
SPEED” appears in the display.
4
Press the SET button.
• The current setting is displayed on the screen. (The setting is 2X
by default.)
MULTI JOG SET
1. Select the source. 2. Enter the Selection
=
CD1
+=
CD2
+=
CD3
+
MULTI JOG SET
1. Select the track. 2. Enter the Selection
3-CD Changer to CDR
Recording Options
Setting the unit to perform
high-speed recording
MIX BALANCE
STANDBY
PHONES LEVEL
MAX MIN
MULTI JOG
+ – POWER
REC LEVEL
2 4 3,5
XL - R5000 CD/CDR MULTIPLE COMPACT DISC RECORDER
1 2 3
4 5 6
7 8
10 +10
9
PLAY MODE REPEAT SET CANCEL
CONTROL
PITCH 0
PITCH +
PITCH – SHIFT REC MUTING
REC
DISPLAY SYNCHRO CD REC
CD EDIT FINALIZE MENU
POWER
CD 1
CD 2
CD 3
CD CDR
2
1
3,5
4
2
REMOTE CONTROL
RM-SXLR5000J
CANCEL
CANCEL
XL-R5000.book Page 23 Wednesday, March 29, 2000 6:37 PM