JVC XL-R5000BK - Manual (Page 35)

30
Englis
h
Once a CD-R has been finalized, further recording on that disc can-
not be performed. However, by erasing the TOC (Table of Con-
tents) on a CD-RW, the disc can be recorded on again.
1
Load a CD-RW into the CDR deck.
• The CD-RW and FINALIZED indicators light for a CD-RW
that has been finalized.
2
When the unit is in the stop mode, press the
MENU button on the main unit (or the DISPLAY/
MENU button on the remote control while
holding down the SHIFT button)
3
Turn the MULTI JOG dial or press the 4 / ¢
button on the remote control until
“UNFINALIZE” appears in the display.
4
Press the SET button.
• “UNFINALIZE?” appears in the display.
• Press the CANCEL button to cancel the procedure and return to
the normal display.
5
Press the SET button again to confirm the
operation.
• “UNFINALIZE” appears in the display and the unfinalization
procedure is performed. The procedure takes about one and a
quarter minutes to perform. During the procedure the length of
the level meter is used to indicate approximately how much
time is remaining unitl unfinalization is complete. Upon com-
pletion, the normal display is returned to.
* known as Sampling Rate Converter.
The FS converter of this unit allows it to convert the digital signals
of sources with sampling frequencies other than 44.1 kHz to the
sampling frequency of 44.1 kHz necessary for it to be recorded to a
CD-R or CD-RW.
When the FS converter is set to “OFF”, the FS converter is
bypassed when the digital signal of the source has a sampling fre-
quency of 44.1 kHz (even if the FS converter is set to “OFF”, the
FS converter cannot be bypassed for digital signals with sampling
frequencies other than 44.1 kHz) and it automatically turns ON if
high-speed recording (DUB-SPEED 2X) from 3CD is started.To
record by bypassing the FS converter, use “DUB-SPEED 1X”
recording. With this setting, the pure digital signal is preserved.
When recording specially encoded discs such as dts
*1 CD, HDCD
CD *2 , etc., be sure to use the following set this CONVERTER to
“OFF” (see step 4) and DUB-SPEED to “1X” (see step 5 on page
23).
When the FS converter is set to “ON”, the FS converter functions
even when the sampling frequency of the digital signal is 44.1 kHz.
The obvious merit of this setting is that it reduces jitter in disc
recording. For this reason, setting this function to “ON” is recom-
mended for most recording purposes.
*1 dts is trademark of Digital Theater Systems, Inc.
*2 HDCD

is registered trademark of Pacific Microsonic, Inc.
1
When the unit is in stop mode, press the MENU
button (or the DISPLAY/MENU button on the
remote control while holding down the SHIFT
button).
Making recording possible
again on a finalized CD-RW
(UNFINALIZE function)
MIX BALANCE
STANDBY
PHONES LEVEL
MAX MIN
MULTI JOG
+ –
POWER
REC LEVEL
2 3
1
4,5
XL - R5000 CD/CDR MULTIPLE COMPACT DISC RECORDER
CANCEL
Bypassing the FS Converter
(Sampling Frequency
Converter*) for More Efficient
Digital Recording
MIX BALANCE
STANDBY
PHONES LEVEL
MAX MIN
MULTI JOG
+ –
POWER
REC LEVEL
1 3,5 2,4
XL - R5000 CD/CDR MULTIPLE COMPACT DISC RECORDER
1 2 3
4 5 6
7 8
10 +10
9
PLAY MODE REPEAT SET CANCEL
CONTROL
PITCH 0
PITCH +
PITCH – SHIFT REC MUTING
REC
DISPLAY SYNCHRO CD REC
CD EDIT
FINALIZE MENU
POWER
CD 1
CD 2
CD 3
CD CDR
1
2,4
3,5
1
REMOTE CONTROL
RM-SXLR5000J
CANCEL
CANCEL
XL-R5000.book Page 30 Wednesday, March 29, 2000 6:37 PM