JVC BR-DV600U - Manual (Page 10)

16
Recorder
BR-DV600
BR-DV600
BR-S800
SR-S365 (U MODEL)
SR-S388 (E MODEL)
BR-DV600
Player
BR-DV600
BR-DV600
BR-DV600
BR-DV600
BR-S800/BR-S500 (+ SA-N50)*
5 Edit adjust setting
The No. 353 <EDIT ADJUST> menu switch must be adjusted according to the configuration of the editing system being
used.
Setting table (when the RM-G800 is used)
Signal connection method
Analog
IEEE 1394
Analog
Analog
Analog
Setting
0 F
0 F
0 F
0 F
---
Setting
4 F
2 F
---
---
3 F
3 CONNECTIONS
DC 12V
PGZ01945
TIMER TIME CODE SPARE
COMPONENT VIDEO
SYNC IN
REC OFF PLAY
DV IN/OUT
REMOTE
AUDIO
2 1
SERIAL
CH 1/3
OUT
OUT
IN IN B-Y IN Y/C
LINE
OUT
OUT MONITOR
CH 2/4
MONITOR OUT
R-Y Y
Video signal
Audio signal
Non-linear editing system
Remote control
5 Non-linear editing system
Material recorded on a MiniDV tape can be captured to a non-linear editing system. The following non-linear editing
systems are able to utilize Super Scene Finder (SSF) data.
• Canopus Corporation: DV Rex RT
• Casablanca
5 Control via the DV connector
• When the DV connector is used for control, assemble editing cannot be performed.
• When the VCR is stopped via the DV connector, a command error message may be returned to the controller. This is not
a malfunction.
Notes on connecting a cable to the [DV IN/OUT] connector
Set the following menu switches, turn the connected equipment ON and then connect the cable to the [DV
IN/OUT] connector. (If two BR-DV600s are connected to each other, it is not necessary to turn them ON.)
Menu switch settings
• When used as a player
Set the No. 108 <VIDEO INPUT SELECT> menu switch to any position except “IEEE 1394”.
(If this switch is currently set to “IEEE 1394”, change the setting and turn the power OFF and ON again.)
• When used as a recorder
Set the No. 108 <VIDEO INPUT SELECT> menu switch to “IEEE 1394”.
• When controlled by another device via the [DV INPUT] connector
Set the No. 050 <REMOTE SELECT> menu switch to “IEEE 1394”.
* To ensure the stability of input signals, install the SA-N50 in the BR-DV600.
17
4 MENU SWITCHES
You can set menu switches using either the on-screen display or the counter display. To set switches on the on-screen display,
you will need to connect a monitor to the VCR’s [VIDEO MONITOR OUT] connector. This section explains how to set switches
using the on-screen display. The same procedures apply to switch setting on the counter display, the only difference being that
each menu switch item is indicated by numeric code rather than by name.
Menu switch group
select screen
0 3 : SYNC SE L ECT
5 0 : REMOTE SE L ECT
0
0
OF F
0 2 : OPERAT I ON LOCK 0
STOP
TCR 1 2 : 0 0 : 0 0 : 0 0
0 0 ~ : SYSTEM
0 0 ~ : T I ME CODE
0 0 ~ : ONSCREEN
M : HOUR METER
3
4
5
H
0 0 ~ : AUD I O 2
0 0 ~ : SERVO / SYSTEM 0
0 0 ~ : V I DEO 1
[SELECT]
[MENU]
[SET]
[MENU]
[SHIFT] U A
US +RS 4 2
TO
2 A J VC B
4-1 Menu switch organization
Menu switch group select screen
Pressing the [MENU] button with the normal screen
displayed brings up the menu switch group select screen.
Select the desired group with the [SHIFT +/–] button.
The selected group number blinks.
Press the [SELECT] button to go to the selected group
menu switch setting screen.
Menu switch setting screen
To access this screen, press the [SELECT] button on the
menu switch group select screen.
Press the [MENU] button to go to the menu switch group
select screen.
Menu switch group select screen
Menu switch setting screen
On-screen display
L I NE
0 8 : V I DEO I NPUT SE L ECT 1
0 3 : SYNC SE L ECT
U A
5 0 : REMOTE SE L ECT
US +RS 4 2
0
0
OF F
0 2 : OPERAT I ON LOCK 0
TO
2 A J VC B
STOP
TCR 1 2 : 0 0 : 0 0 : 0 0
( HOUR METER )
H : DRUM HOUR METER
0 0 0 0 0
D
0H
0 0 : SYSTEM
0 0 : T I ME CODE
0 0 : ONSCREEN
M : HOUR METER
3
4
5
H
0 0 : AUD I O 2
0 0 : SERVO / SYSTEM 0
0 0 : V I DEO 1
[SET]
[MENU]
[SHIFT]
[SELECT] [MENU]
Menu switch setting screen
On-screen display
Switching the
setting screen
[SHIFT] +/–: Item select
SELECT: Changes the setting.
SET:
Enters the setting.
Menu switch display
SHIFT
SET SELECT
SHIFT
MENU
HOLD
AUDIO
MONITOR OUTPUT COUNTER
SHIFT A. DUB
ADVANCE PRESET
L CTL
TC
UB
CH-1/2
CH-3/4 R
MIX MIX
MENU
OVER
OVER
H M S F
AUD LOCK
32k 48k PB NDF
SERVO RF
DEW AUTO OFF
HOLD
CH 2/4
CH 1/3
dB 40 30 20 10 0
D A T A S E T
A B O R T
Counter display
When entered
When data has not
been entered yet
Menu switch setting procedure
1 Press the [SHIFT –/+] button on the menu switch set-
ting screen to select the menu switch you want to set.
[
The selected menu switch number blinks.
2 Press the [SELECT] button to change the set value.
3 Repeat steps 1 and 2 to change any other menu switches.
4 Press the [SET] button to end menu switch setting.
[
The set value is entered and the normal screen is
restored. When entering the data, the indications shown
on the left are displayed. If data has not been entered
and menu switch setting is ended, “Abort” indication is
shown.
To access another group menu switch setting screen without
ending menu switch setting, press the [MENU] button.
For servicing
See the service manual page 1-10 “1.6 SERVICE MENU”.
→