JVC BR-DV600U - Manual (Page 11)

18
4 MENU SWITCHES
4-2 Menu switch details
For switch setting procedures, refer to “Menu switch setting
procedure”.
q
: Factory setting
(00): The number in the bracket shows the set value on the
counter display.
002 OPERATION LOCK
Details: Switches the operation lock ON/OFF.
Setting:
q
OFF (00): The operation lock is OFF: all operations
are enabled.
ON (01): The operation lock is ON: all controls are
disabled except for the [MENU] button.
003 SYNC SELECT
Details: Selects the sync signal during play.
Setting:
EXTERNAL (01): Synchronizes with the signal input
to the [SYNC IN] connector.
q AUTO (03): Switches the synchronization
automatically depending on
whether or not a signal is input to
the [SYNC IN] connector. For
details, refer to page 11.
050 REMOTE SELECT
Details: Selects the remote controller connected to
the [REMOTE] connector on the rear panel.
When the optional SA-K46 RS-232C
interface board is installed at the [REMOTE 1]
connector, some setting indications will change.
Setting:
IEEE 1394 (01): Allows control of this unit with the
controller connected to the [DV IN/
OUT] connector.
RS422A (04): Allows control of this unit with the
controller connected to the
[REMOTE 1] connector.
IEEE 1394 + RS422A (05): Allows control of this
unit with the controllers connected
to the [DV IN/OUT] and [REMOTE 1]
connectors.
JVC BUS (08): Allows control of this unit with the
controller connected to the
[REMOTE 2] connector.
JVC BUS + IEEE 1394 (09): Allows control of this
unit with the controllers connected
to the [REMOTE 2] and [DV IN/
OUT] connectors.
JVC BUS + RS422A (12): Allows control of this unit
with the controllers connected to
the [REMOTE 2] and [REMOTE 1]
connectors.
q JVC BUS + RS422A + 1394 (13): Allows control of
this unit with the controllers
connected to the [REMOTE 2],
[REMOTE 1] and [DV IN/OUT]
connectors.
(When the optional SA-K46 RS-232C interface
board is installed)
IEEE 1394 (01): Allows control of this unit with the
controller connected to the [DV IN/
OUT] connector.
RS232C (02): Allows control of this unit with the
controller connected to the
[REMOTE 1] connector.
IEEE 1394 + RS232C (03): Allows control of this
unit with the controllers connected
to the [DV IN/OUT] and [REMOTE 1]
connectors.
JVC BUS (08): Allows control of this unit with the
controller connected to the
[REMOTE 2] connector.
JVC BUS + IEEE 1394 (09): Allows control of this
unit with the controllers connected
to the [REMOTE 2] and [DV IN/
OUT] connectors.
JVC BUS + RS232C (10): Allows control of this unit
with the controllers connected to
the [REMOTE 2] and [REMOTE 1]
connectors.
q JVC BUS + RS232C + 1394 (11): Allows control of
this unit with the controllers
connected to the [REMOTE 2],
[REMOTE 1] and [DV IN/OUT]
connectors.
108 VIDEO INPUT SELECT
Details: Selects the input video signal.
Setting:
q
LINE (00): Selects video signals input to the
[LINE IN] connector.
Y/C (01): Selects video signals input to the
[Y/C IN] connector.
COMPONENT (02): Selects video signals
input to the [COMPONENT IN]
connector.
IEEE 1394 (03): Selects video and audio signals
input to the [DV IN/OUT]
connector. In this case, analog
audio signals are not input.
125 SETUP (U MODEL)
Details: Sets whether or not the setup is applied to
the analog video signals (composite, Y/C,
component).
Setting:
OFF (00): Does not apply the setup.
q ON (01): Applies the setup. Set to this position to
play back a tape recorded on the GY-
DV500.
Notes:
• This setting affects recording and playback of
analog video signals.
• Picture hue and brightness can be affected if
dubbing is repeated without applying a setup
suitable to video signals.
For servicing
See the service manual page 1-19 “1.11 SET UP SW”.
←
19
4 MENU SWITCHES
4-2 Menu switch details
q : Factory setting
(00): The number in the bracket shows the set value on the
counter display.
212 AUDIO OUT AT SEARCH
Details: Selects whether or not audio is output to the
[AUDIO OUT] and [AUDIO MONITOR OUT]
connectors and headphones jack during
search at speeds above ±1x.
Setting:
OFF (00): No output.
q ON (01): Audio is output.
214 V. FADE
Details: Switches the V. fade function ON/OFF. V.fade
reduces audio noise at the tag recording
during playback.
Setting:
OFF (00): The V. fade function is not activated.
q ON (01): Activates the V. fade function.
245 SAMPLING RATE
Details: Selects the sampling rate frequency when
recording audio digitally.
Setting:
32K (00): Records signals at a 32 kHz sampling
frequency. Set to this position for audio
dubbing on CH3 and CH4.
q 48K (01): Records signals at a 48 kHz sampling
frequency. Audio dubbing is not possible
with this setting.
311 AUTO PLAY
Details: Selects whether or not playback starts
automatically after the tape is rewound to the
beginning.
Setting:
q
SHORT FF (00): The tape stops after short FF.
Auto play does not start.
PLAY (01): Auto play starts. Repeat playback
is available when No. 312 <AUTO
REW> menu switch is set to “ON”.
312 AUTO REW
Details: Selects whether or not the tape is rewound
automatically at tape end during recording or
playback.
Setting:
q
OFF (00):The tape is not rewound automatically.
ON (01): The tape is rewound automatically.
Repeat playback is available when No.
311 <AUTO PLAY> menu switch is set to
“PLAY”.
353 EDIT ADJUST
Details: When this unit is used with an editing
controller and the edit-in point is shifted, this
corrects the play start timing.
Switch setting differs depending on the
configuration of the editing system. For
details, refer to “Edit adjust setting” on page 16.
Setting:
q
0F: No compensation.
1F: The playback start point is delayed by 1 frame.
2F: The playback start point is delayed by 2 frames.
3F: The playback start point is delayed by 3 frames
to the factory set timing.
4F: The playback start point is delayed by 4 frames.
5F: The playback start point is delayed by 5 frames.
6F: The playback start point is delayed by 6 frames.
7F: The playback start point is delayed by 7 frames.
360 AUTO REW AT TIMER
Details: Selects whether or not the tape is automati-
cally rewound when the VCR power is
switched ON in the Timer Play or
Recording Standby mode.
Setting:
q
OFF (00): Playback or recording starts immedi-
ately. The tape is not rewound.
ON (01): Playback or recording starts after the
tape is rewound to the beginning.
363 CONTROLLER SELECT
Details: Selects the setting according to the type of
remote control unit connected via the RS-
422A interface.
Setting:
q
TYPE 1 (00): For the RM-G820.
TYPE 2 (01): For a non-linear editing system.
TYPE 3 (02): Unused.
:
TYPE 8 (07)
396 BATTERY SELECT
Details: When using DC power, set this switch
according to the DC power supply and
battery type.
Setting:
q
12 V (00): Select this setting to use a DC power
supply (AA-G10) or DC 12 V flat shape
type battery.
13.2 V (01): Select this setting to use Anton Bauer
Inc.’s Trimpack 13, ProPac 13.
14.4 V (02): Select this setting to use Anton Bauer
Inc.’s Trimpack 14, ProPac 14 and IDX
Corporation's NP-L46.