JVC GM X50U - Manual (Page 22)

21
Resetting the Function Selection Menu Settings
You can reset all the Function Selection Menu settings at a
time.
1
Press MENU/EXIT (or MENU on the
Monitor) to display the Main Menu.
2
Press 5/∞ to move the cursor (3) to
“FUNCTION SELECT.”
3
Press 3 to display the Function
Selection Menu.
* 1 “ASPECT” does not appear when 720/60p, 720/50p,
1080/60i (1035/60i), or 1080/50i signal is being input
through the COMPONENT/RGB B input terminals.
* 2
“SIGNAL MODE” appears only when VIDEO
A, VIDEO B, or COMPONENT input is selected.
* 3 “SYNC TERM.” appears only when the RGB B
input is selected.
4
Press
5/∞ to move the cursor (3) to
“reset.”
5
Press 3.
The confirmation screen appears.
6
Press
3 again to reset the adjustments.
To cancel the reset, press MENU/EXIT (or MENU on
the Monitor).
7
Press MENU/EXIT (or MENU on the
Monitor) twice to exit the menu
operations.
A r e y o u s u r e ?
" Y E S "
t h e n k e y .
" N O " t h e n k e y . M E N U
r e s e t
Changing the Resistance of the RGB B
Input Terminals
You can set the resistance of the two of the RGB B input
terminals to either HIGH (1 k
Ω) or LOW (75 Ω):
• HD/Cs (Horizontal sync/Composite) terminal
• VD (Vertical sync) terminal.
HIGH is the normal setting. Change the setting to LOW when
you use a long connecting cord and the picture flickers and
blurs on the screen.
1
Press MENU/EXIT (or MENU on the
Monitor) to display the Main Menu.
2
Press
5/∞ to move the cursor (3) to
“FUNCTION SELECT.”
3
Press 3 to display the Function
Selection Menu.
* 1 “ASPECT” does not appear when 720/60p, 720/50p,
1080/60i (1035/60i), or 1080/50i signal is being input
through the COMPONENT/RGB B input terminals.
* 2 “SIGNAL MODE” appears only when VIDEO
A, VIDEO B, or COMPONENT input is selected.
* 3
“SYNC TERM.” appears only when the RGB B
input is selected.
4
Press 5/∞ to move the cursor (3) to
“SYNC TERM.”
5
Press 2/3 to select the terminal
resistance.
Each time you press the button, the resistance alternates
between “HIGH” and “LOW.”
HIGH : Initial setting. Normally select this.
LOW : When using a long connecting cord and the
picture flickering and blurring on the screen.
6
Press MENU/EXIT (or MENU on the
Monitor) twice to exit the menu
operations.
P I C T U R E A D J .
S I Z E / P O S I T I O N A D J .
F U N C T I O N S E L E C T
S T A T U S D I S P L A Y
E N T E R :
M A I N M E N U
S E L E C T : E X I T : M E N U
Cursor ( 3)
C O L O R T E M P .
A S P E C T
S I G N A L M O D E
C O M P O . / R G B B
S Y N C T E R M .
r e s e t
F U N C T I O N S E L E C T
A D J U S T : S E L E C T : E X I T : M E N U
: H I G H
: P A N O R A M I C
: A U T O
: R G B B
: H I G H *
*1 *2 *3
P I C T U R E A D J .
S I Z E / P O S I T I O N A D J .
F U N C T I O N S E L E C T
S T A T U S D I S P L A Y
E N T E R :
M A I N M E N U
S E L E C T : E X I T : M E N U
Cursor ( 3)
C O L O R T E M P .
A S P E C T
S I G N A L M O D E
C O M P O . / R G B B
S Y N C T E R M .
r e s e t
F U N C T I O N S E L E C T
A D J U S T : S E L E C T : E X I T : M E N U
: H I G H
: P A N O R A M I C
: A U T O
: R G B B
: H I G H *
*1 *2 *3
14-21_GM_X50[US].p65 04.1.27, 8:38 AM 21