JVC GM X50U - Manual (Page 74)

29
ENGLISH
To reset the Color-Reverse setting
After step 2 on the left column, proceed as follows:
1 Press 5/∞ to move the cursor (3) to “reset.”
2 Press 3.
The confirmation screen appears.
3 Press 3 again to reset the setting.
To cancel the reset, press MENU/EXIT (or MENU on the
Monitor).
Note:
• The Color-Reverse function requires considerable time to
reduce the afterimage. Deactivate the function temporarily
at intervals of 30 minutes-1 hour and check the screen if the
afterimage still remains or not. Set the function to off if the
afterimage has been reduced.
Refreshing the Screen
After the power is turned off, a whitish image may be left on
the screen. In that case, leave the monitor in a white back state
for a while, and the image will disappear.
You can activate/deactivate the function with the Refresh
On/Off Timer.
1
On the remote control:
Press VOLUME – while holding MENU/
EXIT to display the Setup Menu.
On the Monitor:
Press
2 while holding MENU to display
the Setup Menu.
2
Press 5/∞ to move the cursor (3) to
“REFRESH” (on the second page) then
press
3.
• The Setup Menu consists of two pages. If you keep
pressing 5/∞, you can move to the other page from
the current page.
2
Press 5/∞ to move the cursor (3) to
“COLOR-REVERSE” (on the second
page), then press
3.
• The Setup Menu consists of two pages. If you keep
pressing 5/∞, you can move to the other page from
the current page.
3
Press 5/∞ to select the item you want
to set and set the item as follows.
COLOR-REVERSE
You can activate/deactivate the function manually.
Press
2/3 to select the desired setting.
ON : The function is activated immediately after
exiting the menu operations.
OFF : The function is deactivated.
TIMER : Select this when you use the Color-Reverse
On/Off Timer.
Note:
• Set the clock (see page 26) and select “TIMER,” before
using the Color-Reverse On/Off Timer.
START SET
You can activate/deactivate the Color-Reverse On Timer.
Press
2/3 to select “ON” or “OFF.”
ON : The function is automatically activated at the
time set in “START TIME.”
OFF : The Color-Reverse On Timer is deactivated.
START TIME
You can adjust the time to activate the function.
• Set the hour and minute following steps 4 to 6 in
“Setting the Clock” (page 26).
END SET
You can activate/deactivate the Color-Reverse Off Timer.
• Press
2/3 to select “ON” or “OFF.”
ON : The function is automatically deactivated at the
time set in “END TIME.”
OFF : The Color-Reverse Off Timer is deactivated.
END TIME
You can adjust the time to deactivate the function.
• Set the hour and minute following steps 4 to 6 in
“Setting the Clock” (page 26).
4
Press MENU/EXIT (or MENU on the
Monitor) repeatedly to exit from the
menu operations.
P I X E L S H I F T
P O W E R S A V E
C O L O R - R E V E R S E
R E F R E S H
r e s e t
a l l r e s e t
H O U R M E T E R x 1 0 0 h
S E T - U P M E N U 2 / 2
A D J U S T : S E L E C T : E X I T : M E N U
: O F F
: O F F
: 1 2 3
M O D E L :GM-X50 V e r . A
C A T E G O R Y . E
S T A T U S D I S P L A Y
C O N T R O L L O C K
R E M O T E S W I T C H
H D S I G N A L M O D E
F A N S P E E D
W H I T E B A L A N C E
T I M E R
S E T - U P M E N U 1 / 2
A D J U S T : S E L E C T : E X I T : M E N U
: O F F
: O F F
: M O D E 1
: 1 0 8 0 i
: L O W Cursor ( 3)
P I X E L S H I F T
P O W E R S A V E
C O L O R - R E V E R S E
R E F R E S H
r e s e t
a l l r e s e t
H O U R M E T E R x 1 0 0 h
S E T - U P M E N U 2 / 2
A D J U S T : S E L E C T : E X I T : M E N U
: O F F
: O F F
: 1 2 3
M O D E L :GM-X50 V e r . A
C A T E G O R Y . E
(To be continued on the next page)
A r e y o u s u r e ?
" Y E S "
t h e n k e y .
" N O " t h e n k e y . M E N U
r e s e t
22-31_GM_X50E.p65 04.3.14, 3:30 PM 29