Sony RDR-HXD860 - Manual (Page 107)

C:\2886042111HXD860CEK\01GB-
HXD860CEK\130ADD.fm
master page=right
specdef 20060621
RDR-HXD860
2-886-042-11(1)
107
A
d
d
iti
o
n
a
l In
fo
rm
a
tio
n
The picture does not fill the screen, even
though the picture size is set in “TV Type”
of the “Video Output” in the “Video”
setup.
, The picture size of the title is fixed.
The picture is black and white.
, Check that “Line1 Output” of the “Scart
Setting” in the “Video” setup is set to the
appropriate item that conforms to your
system (page 96).
, If you are using a SCART cord, be sure to
use one that is fully wired (21 pins).
There is no sound.
, Re-connect all connections securely.
, The connecting cord is damaged.
, The input source setting on the amplifier or
the connection to the amplifier is incorrect.
, The recorder is in reverse play, fast-
forward, slow motion, or pause mode.
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL)/HDMI
OUT jacks, check the “Audio Connection”
settings in the “Audio” setup (page 97).
, The recorder supports only MP3 audio and
MPEG audio for DivX video files. Press
AUDIO and select MP3 audio or MPEG
audio.
No sound is output from the HDMI OUT
jack.
, Try the following: 1 Turn the recorder off
and on again. 2 Turn the connected
equipment off and on again. 3 Disconnect
and then connect the HDMI cord again.
, The HDMI OUT jack is connected to a DVI
device (DVI jacks do not accept audio
signals).
, The equipment connected to the HDMI
OUT jack does not conform to the audio
signal format, in this case set
“Audio(HDMI)” of “Audio Connection” to
“PCM” in the “Audio” setup (page 99).
Sound distortion occurs.
, Set “Audio ATT” in the “Audio” setup to
“On” (page 97).
Sound is noisy.
, When playing a CD with DTS sound tracks,
noise will come from the LINE 2 OUT R-
AUDIO-L jacks, LINE 1 – TV jack, or
LINE 3 jack (page 62).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“Audio DRC” in the “Audio” setup to “TV
Mode” (page 99).
, Set “Audio ATT” in the “Audio” setup to
“Off” (page 97).
An alternate audio track cannot be
recorded or played.
, When recording from connected
equipment, set “Line Audio Input” in
OPTIONS menu to “Bilingual” (page 58).
, Multilingual tracks (main and sub) cannot
be recorded on DVD+RWs, DVD-RWs
(Video mode), DVD+Rs, or DVD-Rs
(Video mode). To record the language, set
“Bilingual Recording” of the “DVD Rec.
Settings” in the “Recording” setup to
“Main” or “Sub” before recording
(page 100). To record both the main and sub
sounds, record on DVD-RWs/DVD-Rs
(VR mode).
, Any discs other than the HDD or DVD-
RWs/DVD-Rs (VR mode) cannot be used
for recording both main and sub sounds. To
record on the HDD, set “Bilingual
Recording” of the “HDD Rec. Settings” in
the “Recording” setup to “Main+Sub”
(page 100).
, If you have connected an AV amplifier to
the DIGITAL OUT (COAXIAL) jack and
want to change the audio track for HDD/
DVD-RWs/DVD-Rs (VR mode) during
playback, set “Dolby Digital” of the “Audio
Connection” in the “Audio” setup to “D-
PCM” (page 98).
The sound is breaking up.
, The signal strength is low.
, Check aerial installation.
Sound
,continued