Setting time codes – Sony HDW-F500 User Manual
Page 65
Chapter 4
Menu Settings
4-23
Chapter 4 Menu Settings
Data entry
window
SET is displayed.
Å I N 0 0 : 0 1 : 1 0 : 0 0 Å O U T 0 0 : 0 2 : 1 0 : 0 0
P L A Y L O C K
T I M E R
S E L
T C
C H . C O N D
G R E E N
0 1 0 0 3 0 0 0
T C
T C R V I T C 2 F D F 1
I N 0 0 : 0 1 : 1 0 : 0 0 O U T 0 0 : 0 2 : 1 0 : 0 0
01
Ó
04
µ
58
ß
00
ƒ
T I M E R
R E S E T
T I M E R
S E T
T I M E R
H O L D
T C
S E L
V I T C
T C G
S O U R C E
i n t - L
T C G
M O D E
p r s t
R U N
M O D E
r e c
D F / N D F
D F
V I T C
T C G
R E M A I N - T
L 1 1 3 m i n
Å I N 0 0 : 0 1 : 1 0 : 0 0 Å O U T 0 0 : 0 2 : 1 0 : 0 0
P L A Y L O C K
T I M E R
S E L
T C
C H . C O N D
G R E E N
S E T 0 1 0 0 3 0 0 0
T C
T C R V I T C 2 F D F 1
I N 0 0 : 0 1 : 1 0 : 0 0 O U T 0 0 : 0 2 : 1 0 : 0 0
01
Ó
04
µ
58
ß
00
ƒ
T I M E R
R E S E T
T I M E R
S E T
T I M E R
H O L D
T C
S E L
V I T C
T C G
S O U R C E
i n t - L
T C G
M O D E
p r s t
R U N
M O D E
r e c
D F / N D F
D F
V I T C
T C G
R E M A I N - T
L 1 1 3 m i n
Setting time codes
To set time codes, select prst with the
[F7] (TCG
MODE) button in the TC menu and then follow the
steps below.
Note
• Set the
[F8] (RUN MODE) button to rec before
setting the time data for recording. When you select
rec, time data advances from a set value only during
recording. When you select free, time code advances
in real time after the initial value has been set.
• During recording, VITC is always written to the
AUX data area of the video signal.
Setting time codes
1
Press the
[F1] (TIMER SEL) button to select the
TC (time code) to be set.
2
Enter the new setting in the data entry window
with the numeric buttons.
For example, to enter 01H00M30S00F, press 1, 0,
0, 3, 0, 0, 0. (The leading 0 is not required. When
the entered value is less than eight digits, the
leading digit(s) is (are) set to 0 when you press the
SET button.)
To cancel entered values
Press the CLR button.
3
Press the SET button to set the entered
value.
If you pressed the + or – button, then entered a
value, the result of calculation appears in the
display.
4
Press the
[F3] (TIMER SET) button.
The input value is set as the time code and appears
in the time data display section.
Notes
• Time codes from an external time code generator
cannot be set.
• Time codes cannot be set when the internal time code
generator is locked to external time codes or to time
codes read by the time code reader.
1
3
4
2