Sony DREAM MACHINE ICF-CD3IP User Manual

Fm/am cd clock radio, Icf-cd3ip, Features

Advertising
background image

Owner’s Record

The model number and the serial number are located on the

bottom.

Record the serial number in the space provided below. Refer

to them whenever you call upon your Sony dealer regarding

this product.
Model No. ICF-CD3iP

Serial No. ________________________________

For customers who purchased this product in the

USA

Please register this product on line at

http://www.sony.com/productregistration.

Proper registration will enable us to send you

periodic updates about new products, services, and

other important announcements. Registering your

product will also allow us to contact you in the

unlikely event that the product needs adjustment

or modification. Thank you.

WARNING

To reduce the risk of fire or electric shock, do

not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation opening of the apparatus with

newspapers, tablecloths, curtains, etc. Do not

place the naked flame sources such as lighted

candles on the apparatus.

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing,

and do not place objects filled with liquids, such

as vases, on the apparatus.
Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.
As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main plug

from the AC outlet immediately.
You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

CAUTION

 The use of optical instruments with this

product will increase eye hazard.

 Danger of explosion if battery is incorrectly

replaced. Replace only with the same or

equivalent type.

This symbol is intended to alert the user

to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that

may be of sufficient magnitude to constitute

a risk of electric shock to persons.
This symbol is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

CLASS1M INVISIBLE LASER RADIATION

WHEN OPEN DO NOT VIEW DIRECTRY

WITH OPTICAL INSTRUMENTS.

Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

INFORMATION

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and

can radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

— Reorient or relocate the receiving

antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING

 Replace the battery for the clock backup with a

Sony CR2032 lithium battery, and the battery

for the remote commander with a Sony CR2025

lithium battery. Use of another battery may

present a risk of fire or explosion.

 Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.

 Do not expose the battery to excessive heat

such as direct sunlight, fire or the like.

 Dispose of used battery promptly. Keep away

from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the manufacturer’s

instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized

plug has two blades with one wider than the

other. A grounding type plug has two blades

and a third grounding prong. The wide blade

or the third prong are provided for your safety.

If the provided plug does not fit into your

outlet, consult an electrician for replacement

of the obsolete outlet.

10) Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

11) Only use attachments/accessories specified by

the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms

or when unused for long periods of time.

14) Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way, such

as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

For the state of california, USA only

Perchlorate Material –special handling may apply, See

www.dtsc.ca.gov/hazardouswaste/perchlorate

Perchlorate Material: Lithium battery contains

perchlorate

Features

 Brightness control (High/Mid/Low)

 Supplied audio cable for digital music players

 Built-in CD player with CD-R/RW playback

function

 FM/AM 2-band digital tuner

 30 Station Presets (20 FM, 10 AM)

 Automatic Time/Daylight Saving Time Setting

 No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed

 Extendable Snooze time from 10 to 60 min

Precautions

 Play the unit on the power source specified in

“Specifications”.

 To disconnect the AC power cord (mains lead),

pull it out by the plug, not the cord.

 The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the player itself has

been turned off.

 The nameplate and important information

concerning safety are located on the bottom

exterior.

 Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic coding

or spring-wound watches away from the unit to

prevent possible damage from the magnet.

 Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive dust,

mechanical vibration, or shock.

 Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit on

a surface (a rug, a blanket, etc.) or near

materials (a curtain) which might block the

ventilation holes.

 Should any solid object or liquid fall into the unit,

unplug the unit and have it checked by qualified

personnel before operating it any further.

 To clean the casing, use a soft cloth dampened

with a mild detergent solution.

 Never touch the wire of the external FM

antenna during a thunderstorm. Furthermore,

immediately disconnect the AC power cord

from the radio.

NOTES ON LITHIUM BATTERY

 Wipe the battery with a dry cloth to assure a

good contact.

 Be sure to observe the correct polarity when

installing the battery.

 Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

If you have any questions or problems concerning

your unit, please consult your nearest Sony dealer.

Troubleshooting

Should any problem persist after you have made

the following checks, consult your nearest Sony

dealer.
The clock flashes “AM 12:00” due to a power

interruption.
 The battery is low. Replace the battery. Remove

the old battery and install a new one.

The CD, radio, iPod or buzzer alarm does not

sound at the preset alarm time.
 Check that “ALARM A” or “ALARM B” is

properly displayed.

The CD, radio or alarm of iPod is activated

but no sound comes on at the preset alarm

time.
 Has VOLUME been adjusted?
The CD player does not operate.
 Did you close the CD compartment lid?

 Did you insert the disc correctly?

The disc should be inserted with the label side

up.

 Dusty or defective disc — Clean the disc with

an optional cleaning cloth. Wipe the disc from

the center out.

 Take out the CD and leave the CD

compartment open for about an hour to allow

condensation to evaporate.

There is no sound from the iPod.
 Make sure the iPod is securely connected.

 Adjust the VOLUME.
The iPod cannot be operated with this unit.
 Make sure the iPod is securely connected.
The iPod cannot be charged.
 Make sure the iPod is securely connected.
When daylight saving time begins, the clock

does not employ the daylight saving time

automatically.
 Make sure the clock is set correctly.

 Press and hold CLOCK and BRIGHTNESS/

TIME ZONE simultaneously for at least two

seconds to employ the DST function.

Specifications

Audio power specifications

POWER OUTPUT AND TOTAL HARMONIC

DISTORTION

With 20-ohm loads, both channels driven from

150-10,000 kHz; rated 0.7W per channel-

minimum RMS, with no more than 10% total

harmonic distortion.

CD player section

System

Compact disc digital audio system
Laser diode properties

Emission duration: Continuous

Laser output: Less than 44.6 µW(This output is

the value measurement at a distance of 200 mm

from the objective lens surface on the optical

pick-up block with 7 mm aperture.)
Number of channels

2
Frequency response

20 - 20 000 Hz +1/–2 dB

Wow and flutter

Below measurable limit

4-270-865-12(1)

©2008 Sony Corporation Printed in China

ICF-CD3iP

FM/AM CD

Clock Radio

Operating Instructions

Dream Machine is a trademark of Sony Corporation.

This unit includes a preinstalled Sony Lithium battery (CR2032) as back-up power source for the clock, which is preset

to EST (Eastern Standard Time) at the factory. And this battery is considered part of the product.

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not dismantle

or roll up the antenna.

1

Remove only the loop part from the

plastic stand.

2

Set up the AM loop antenna.

3

Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected to

either terminal.

A

B

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4

Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provide good

reception.

 Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To keep good time, this unit contains one CR2032

battery inside of the unit as a backup power

source.

The battery keeps the clock operating in the event

of a power interruption.

Knowing when to replace the

battery

When the battery becomes weak, “” appears in

the display.

If a power interruption occurs while the battery is

weak, the current time and alarm will be erased.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire or

explosion.
Note

If “AM 12:00” flashes in the display when the unit

is connected to AC outlet for the first time, the

battery may be weak. In this case, consult your

Sony dealer.

Replacing the battery

1

Open the CD compartment lid. (See Fig.

-)

2

Keep the AC plug connected to the AC

outlet and use a screwdriver to remove

the screw that secures the battery holder

at the bottom of the unit. (See Fig. -

)

3

Push the exhausted battery out from the

bottom of the battery holder and insert a

new battery with the  side facing up.

(See Fig. -)

4

Insert the battery holder back into the

unit and secure it with the screw. (See

Fig. -)

5

Press CD, iPod&iPhone, RADIO BAND,

AUDIO IN or SNOOZE/DATE/SLEEP

OFF to turn “

” off in the display.

Section for iPod

DC out: 5V

MAX: 500mA (AC only)

Radio section

Frequency range

Band

Frequency

Channel step

FM

87.5 – 108 MHz 0.1 MHz

AM

530 – 1 710 kHz 10 kHz

General

Speaker

Approx. 3.8 cm (1

1

/

2

inches) dia. 20 Ω

Input

AUDIO IN jack (ø 3.5 mm stereo minijack)
Power output

1 W + 1 W (at 10% harmonic distortion)
Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Dimensions

Approx. 145 Ч 156.8 Ч 115.8 mm (w/h/d)

(5

3

/

4

Ч 6

1

/

4

Ч 4

5

/

8

inches) not including

projecting parts and controls
Mass

Approx. 1.3 kg (2 lb 13 oz) including power

supply unit
Supplied accessories

Remote commander (1)

AM loop antenna (1)

Audio connecting cable (1)

Universal Dock Adapter for iPhone (1)

Universal Dock Adapter for iPhone 3GS &

iPhone 3G (1)

Universal Dock Adapter for iPhone 4S & iPhone 4

(1)
Design and specifications are subject to change

without notice.

Compatible iPod/iPhone

models

Compatible iPod/iPhone models are as follows.

Update your iPod/iPhone to use the latest

software before you use it.

iPod touch (4th generation)

iPod touch (3rd generation)

iPod touch (2nd generation)

iPod touch (1st generation)

iPod nano (6th generation)*

iPod nano (5th generation)

iPod nano (4th generation)

iPod nano (3rd generation)

iPod nano (2nd generation)

iPod nano (1st generation)

iPod with video

iPod with color display

iPod with click wheel

iPod classic

iPod mini

iPhone 4S

iPhone 4

iPhone 3GS

iPhone 3G

iPhone
* The iPod nano (6th generation) cannot be

controlled by the remote when the command of

“MENU,” “,” “,” and “ENTER” is pressed.

Notes
 In these Operating Instructions, “iPod” is used

as a general reference to functions of iPod on

the iPod and iPhone, unless otherwise specified

by the text or illustrations.

 The connector of the unit is for sole use for

iPod. When you use devices that do not match

with the connector, connect to the AUDIO IN

terminal of this unit with the supplied audio

connecting cable.

 Sony cannot accept responsibility in the event

that data recorded to iPod is lost or damaged

when using an iPod connected to this unit.

The CD, iPod & iPhone and

VOLUME + buttons have a tactile dot.

CR2025

No Power No Problem is a trademark of Sony Corporation.

Preparing the remote

commander

Before using the card remote commander for the

first time, remove the insulation film. (See Fig.

-)

When to replace the battery

With normal use, the battery (CR2025) should

last for about six months. When the remote

commander no longer operates the unit, replace

the battery with a new one. (See Fig. -)

Notes
 Do not charge the battery.

 When you are not going to use the remote

commander for a long time, remove the battery

to avoid any damage caused by leakage and

corrosion.

If the time in the display is

incorrect after the battery is

changed (Reset)

Press the Reset button with a pointed device. The

Reset button is in the small hole located in the

battery compartment.
Note

When you replace the battery, do not disconnect

the plug from the AC outlet. Otherwise, the

calendar, current time, alarm and station presets

will be erased.
Battery Warning

If the unit is to be left unplugged for a long time,

remove the battery to avoid undue battery

discharge and damage to the unit from battery

leakage.
WARNING

There is a danger of explosion if the battery is

incorrectly replaced.

Replace only with the same or equivalent type

recommended by the equipment manufacturer.
If the battery compartment lid comes off

The battery compartment lid is designed to come

off when opened with excessive force. To put it

back on, see the illustration.

1

Insert the left hook of the lid into the left

hole in the unit.

2

Insert the right hook into the right hole.

3

Confirm the lid is securely attached.

CR2032

Advertising
This manual is related to the following products: