Kenwood KRF-V4550D - Manual (Page 19)

19
Operations
Muting the sound
The MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
To cancel
Press the MUTE key again so that the "MUTE" indicator goes off.
• Muting can also be canceled by adjusting the volume.
Blinks
SOURCE DIRECT playback (analog sources only)
Use this function to pass the source material direct to the amplifier,
bypassing any audio processing.
To cancel
Press the SOURCE DIRECT key.
• When you press the LISTEN MODE, SOUND, or SET UP keys, or
switch to another input source, SOURCE DIRECT playback will be
canceled.
Listening with headphones
1 Press the SPEAKER key so that the speaker indicator goes off.
2 Connect headphones to the PHONES jack.
• If you turn off all of the speakers when in the surround mode, the
mode is canceled as well, resulting in stereo playback.
• The speakers do not switch off during the 6ch INPUT mode.
Select the other input mode. 7
3 Use the VOLUME CONTROL (VOLUME) to adjust the volume.
1 Use the INPUT SELECTOR knob to select the source (other than
"MD/TAPE") you want to record.
2 Set the cassette deck to record.
3 Start playback, then start recording.
Recording audio (analog sources)
Recording
Recording a music source
1 Press the MONITOR key.
2 Use the INPUT SELECTOR knob to select a source other than
"MD/TAPE."
3 Start playback on the cassette deck connected to the MONITOR
jacks and start recording on the cassette deck connected to the
MD/TAPE jacks.
Recording tapes or MD (with MONITOR function)
1 Use the INPUT SELECTOR knob to select "MD/TAPE."
2 Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck connected to the
VIDEO2/MONITOR jacks.
MONITOR = MD/TAPE recording
MD/TAPE = MONITOR recording
• To copy tapes using a double cassette deck, refer to the instruction
manual of the double cassette deck.
MONITOR function (analog sources only)
You can connect a cassette deck or graphic equalizer to the VIDEO2/
MONITOR jacks of the receiver. If a graphic equalizer is connected,
the MONITOR key should be left in the on position. Alternately, if a
cassette deck equipped with a 3-head system is connected to the
VIDEO2/MONITOR jacks, you will be able to monitor the just-
recorded signal while making recordings on the cassette deck. By
switching the MONITOR key on and off, you can compare the sound
of the source signal and the just-recorded signal. For more informa-
tion, refer to the instruction manual of the connected component.
Press the SOURCE DIRECT key again.
• If SOURCE DIRECT playback was activated when using a surround
mode, cancelling it reactivates the previous surround mode.
Normal playback
LFE
C
S RS LS
TI.VOL B
CLIP
RDS EON PTY
TP TA NEWS
SW
L SP R
MUTE
INPUT SELECTOR
MONITOR
S.DIRECT
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
DSP
MEMO
ST.
TUNED
AUTO SOUND AUTO
STEREO MONITOR
Make sure the SP indicators
are turned off.
When recording a music source, switch the VIDEO2/MONITOR
setting to "MONITOR" .
7
When recording a music source, switch the VIDEO2/MONITOR
setting to "MONITOR".
7
STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND AUTO
S.DIRECT
SW
R L
LFE
C
S RS LS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
A SP
*4967/01-/EN 3/19/01, 6:34 PM 19