Lennox Hearth Winslow (PS40) - Manual (Page 5)

5
FEATURES AND SPECIFICATIONS
CAUTION
THE USE OF UNAPPROVED, DIRTY, WET AND/OR
HIGH SALT CONTENT FUEL WILL VOID THE WAR-
RANTY!
Installation Options
• Residential
• Vented vertical and horizontal (see venting instructions)
• Manufactured home and mobile home
• Thermostat or manual operation
• Bedrooms
Heating
• Max. feed rate is 4.7 pounds/hour or 39,500 BTU/hour
• Min. feed rate is 1.8 pounds/hour or 15,120 BTU/hour
Venting
This stove is approved for venting with Type L and Type PL pellet vent
pipe listed to UL 641 and ULC S609. We recommend the use of venting
products manufactured by Security Chimneys International.. The flue
collar on the stove accepts 3” diameter pipe.
The combustion air for this stove is drawn through a pipe at the lower
rear of the stove. For mobile home installations a 3” ID flex line or pipe
must be attached to the stove’s air intake to draw air from outside the
house. The vent pipe can be installed vertically or horizontally (see Venting
section for recommended installations).
Note: When installing this stove at altitudes of 4000 feet and above, we
suggest the use of 4” pellet vent.
Thermostat
This stove can be operated manually or with a thermostat.
Lighting
This stove is equipped with an electric self igniter for ease of ignition.
Fuel Specifications
This stove is designed to burn wood pellet fuel. In addition, a corn/wood
pellet mixture, with a maximum of 50 percent corn can be burned. Burning
any other fuel that is not approved for use with this appliance will void the
appliance warranty. IMPORTANT: The corn/wood mix needs to be mixed
evenly before being put in the Winslow™ pellet stove hopper.
Wood Pellet Specifications: This appliance has been designed to burn
wood residue pellets with up to 3% ash content. Dirty fuel will adversely
affect the performance of the stove. Any questions regarding pellet fuel
Wood pellets manufactured to the pellet fuels institute (P.F.I.) certification
standard are available in two grades, Standard and Premium. The primary
difference between the two is the ash content of the pellets.
The P.F.I. specification for standard grade and premium grade residential
pellet fuel is as follows:
• CHLORIDES (Salt): Less than 300 p.p.m. to avoid stove and vent
rusting.
• BULK DENSITY: 40 lb. / Cu. Ft. minimum
• MOISTURE CONTENT: 8% maximum
• ASH CONTENT: < 3% maximum (standard grade) < 1% maximum
(premium grade)
• FINES: 0.5% maximum through a 1/8” screen
• BTU CONTENT: There are a number of variations in pellet fuels that are
not included in PFI standards. For example, BTU (heat value) content
may range from just under 8,000 to almost 9,000 Btu, depending upon
species and region of the country and other variables.
Corn Specifications: Use only clean-shelled corn with a moisture content
less than 15% and approximate fuel value of 7000 BTU/lb (16,200 kJ/kg).
Do not attempt to burn corn with higher moisture content or burn lesser
grade fuels. Do not burn other types of agricultural pellets or by-products
(alfalfa, cherry pits, olive pits, nut shells, etc.) as they are not permitted
to be burned in these appliances.
Weight - 305 pounds
Hopper Capacity - 60 pounds
Listing information
The Winslow™ PS40 stove is safety tested and listed with the following
agencies;
• OMNI-Test Laboratories, Inc., Portland, Oregon to ASTM E 1509
• US EPA List of Approved Wood Heating Appliances
• List of Colorado Approved Pellet Stoves
Appearance Choices
The Winslow PS40 stove can be ordered with the following door trims
and grills, log set and brick panel options:
Door Trim Kits Grill Kits
Black .......................79038 Black ............................ 79000
Gold .......................79034 Gold ............................. 79001
Nickel .....................79037 Nickel .......................... 79002
Brushed Nickel ........79035 Brushed Nickel ............ 79022
Black Nickel ............79036 Black Nickel ................. 79039
Log Set .............................. H5142
Brick Panel Kit ..................... 79030