Messages – Panasonic DMP-BD605 User Manual

Page 40

Advertising
background image

RQT9378

40

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.

On the television

Page

Authorization Error

This unit is not authorized

to play this title.

≥ [DivX]: You are trying to play the DivX VOD content that was purchased with a

different registration code. You cannot play the content on this unit.

26

Cannot play.

≥You inserted an incompatible disc (Discs recorded in PAL video, etc.).

6, 7

Cannot display on this unit.

≥You tried to play a non-compatible image.
≥Confirm “SD” on the unit’s display is not blinking and re-insert the card.

7, 38

No disc is inserted.

≥The disc may be upside down.

Rental Expired.

≥ [DivX]: The DivX VOD content has zero remaining plays. You cannot play it.

26

$

This operation is not

available.

≥Some operations are unsupported by the unit. For example;

– [BD-V]: During playback, reverse slow-motion or reverse frame-by-frame is not possible.

20

$

This operation is

prohibited by this disc.

≥Depending on the disc, you may not be able to perform search or skip when film

previews and warning screens are being played back.

20

Cannot connect.

Please check the

connection of the LAN
cable.

≥When a hub is used but its Link lamp does not light up, check the cable

connection, LAN terminal connection, cable itself (a cross over cable may be
used by mistake), etc.

16

IP address is not set.

≥The “IP Address” in “IP Address/DNS Settings” is “---. ---. ---. ---”. Set the “IP

Address”, “Subnet Mask”, and “Default Gateway”. (Select the automatic address
acquisition if necessary.)

17

Cannot obtain IP address

using DHCP.

Please check the
connection or router

settings.

≥If you use a hub, then check the connection between the hub and the router.

–Use the UPLINK port of the hub to connect to a router.
–Check whether or not the hub’s Link lamp lights up. If it does not light up, then

check the cable connection, LAN terminal connection, cable itself (a cross over
cable may be used by mistake), etc.

≥If the above conditions are OK, then the router may not operate in DHCP mode.

Check the router settings and operation. You may reset the router to restore it to
normal.

16

16

This IP address is already in

use.

Please check the IP address
setting.

≥This unit’s IP address is used by another device. Check the IP addresses of this

unit, personal computers, and routers, etc. If necessary, reconfigure them to
avoid IP addresses from being duplicated.

Unable to perform

Connection Test.
Please try again.

≥Turn the unit off. Remove the power cord and reconnect it and try again. If the

same symptom persists, then consult your dealer.

IP address not set correctly.

Connection Test was
unsuccessful. No reply

from host.

Please check the
connection or router

settings.

≥If you use a hub, then check the connection between the hub and the router.

–Use the UPLINK port of the hub to connect to a router.
–If the hub’s Link lamp does not light up, then check the cable connection, LAN

terminal connection, cable itself (a cross over cable may have been used by
mistake), etc.

≥Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP

Address/DNS Settings”.

≥If the MAC address information is required, then press [SETUP] to display the

“Network” menu.

16

17

17, 35

Network connection

refused.
Please confirm Setup

“BD-Live Internet Access.”

≥When you set “BD-Live Internet Access” to “Allow (Limited)” and play BD-Live

contents which do not have a content owner certificate, the Internet access of the
content is not allowed. If you allow the content to connect to Internet, set “BD-Live
Internet Access” to “Allow (ALL)”.

32

Unable to check for latest
firmware version.

Please try again later.

≥The firmware download server is currently unavailable. Please try again later.

High Clarity Sound is

effective.

Analog video output is
turned off when

playback starts.

≥“High Clarity Sound” in setup menu is set to “Enable”, and “High Clarity Sound” in

on-screen menu is set to “On”.

31, 33

RQT9378~Body_mst.fm 40 ページ 2008年12月25日 木曜日 午後3時23分

Advertising