Pentair MT User Manual
Page 14
Page 14
Pentair Water Commercial Pool and Spa
SECTION 6.
Conversion of Model MT Pool Boilers
From Indoor to Outdoor Models
Please read the following instructions with
Figure 11. Figure 12 shows the conversion completed.
Please follow the instructions in their numerical order,
failure to do this will cause problems on assembly.
6A. SECTION I
(See Figure 11)
1.
Remove top panel. (1)
2.
Remove front and rear upper panels, (2).
3.
Remove front and rear wings LH & RH, (3).
4.
Remove diverter assembly, (4 ).
5.
Remove outer screw from upper end panel at
junction with lower end panel.
6.
Remove disconnect all probes and wires going to
castings and gas train.
7.
Remove control box assembly - front of boiler
(not shown).
6B. SECTION II
(See Figure 12)
1.
Install front LH & RH extension panels (flush
with top of upper end panel). (18)
2.
Install rear LH & RH extension panels (flush
with top of upper end panel). (15) (pick up holes
provided into LB upper and lower end panels)
3.
Install front bottom panel. (21)
4.
Install rear bottom panel. (14)
5.
Install front inner baffles (2) 4" from ends. (17)
6.
Install rear inner baffle (1) 2" from ends. (16)
7.
Install front LH & RH upper spacers. (27)
8.
Install rear LH & RH upper spacers. (7)
9.
Install front flue collector extension (screw onto
flange of lower flue collector only). (28)
10.
Install rear flue collector extension (screw onto
flange of lower flue collector only). (8)
11.
Install rear upper panel and remaining screws
from flue collector extension. (12)
12.
Install middle rear panel. (13)
13.
Install front panel making sure opening for
removable panel is square. (19)
14.
Install front stiffener (184) 2450 and up.
15.
Install remaining screws from flue collector
extension.
16.
Install rear top half. (panel-5)
17.
Install front top half. (panel-6)
18.
Install front wire (26) mesh using angle (24) at
top and strap (25) at bottom (mesh to be inserted
under angles of wind baffle stand offs).
19.
Install rear mesh same as Step 18.
20.
Install front LH & RH wind baffle stand off. (23)
21.
Install rear LH & RH wind baffle stand off. (23)
22.
Install front and rear wind baffles. (22)
23.
Install middle rear baffle stand off. (11)
24.
Install middle rear baffle. (10)
25.
Install wires control box parts onto control panel
(not shown).
26.
Install control panel assembly using holes and
bushings provided in RH extension panel for
probes and wires (not shown).
27.
Install removable panels. (20)
Figure 11. Removal of Indoor Parts.
PARTS LIST FOR CONVERSION
KIT - INDOOR TO OUTDOOR (See Figure 12)
Key No.
Part No.
5 ................................................................... 20017100
6 ................................................................... 20016900
7 ................................................................... 20015101
................................................................... 20015102
8 ................................................................... 20016700
9 ................................................................... 20017200
10 ................................................................. 20017300
11 ................................................................. 20017700
12 ................................................................. 20016500
13 ................................................................. 20016600
14 ................................................................. 20016300
15 ................................................................. 20014301
.................................................................. 20014302
16 ................................................................. 20015200
17A Left Front Baffle
(Single Inlet Manifold) .........
20015300
17B Right Front Baffle
(Single Inlet Manifold) ........
20022300
17C Left Front Baffle
(Split Inlet Manifold) ............
20022000
17D Right Front Baffle
(Split Inlet Manifold) .........
20022100
18 ................................................................. 20014601
.................................................................. 20014602
19 ................................................................. 20016100
20 ................................................................. 20018000
21 ................................................................. 20016200
22 ................................................................. 20017200
23 ................................................................. 20017600
24 ................................................................. 20018200
25 ................................................................. 20018300
26 ................................................................. 20018600
27 ................................................................. 20015001
.................................................................. 20015002
28 ................................................................. 20016800