Panasonic DMR-E100H - Manual (Page 63)

63
RQT6986
Ref
e
rence
Error messages
On the television Page
On the unit’s display
Error has occurred. Please
press ENTER. ≥ A serious, but temporary error has occurred and one of the unit’s safety devices has activated.
Press [ENTER]. The unit switches to the standby mode. Press [
Í , DVD POWER] to turn the
unit on again.
—
No disc.
No valid disc. ≥ The disc is upside down. 14
No PC card.
No valid PC card.
No SD card.
No valid SD card. ≥ The card is not inserted. If this message is displayed with a compatible card already inserted,
turn off the power, remove and then re-insert the card.
≥ The card inserted is not compatible or the card format does not match.
≥ Format the card.
22
11
40, 42
This is non-recordable disc. ≥ The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R.
≥ You cannot format a microdrive or mobile hard disk on this unit.
10
—
This disc is not formatted
properly.
Unable to format.
No disc can be read.
This disc cannot be read. ≥ You inserted an incompatible disc.
≥ An unformatted DVD-RAM is in the tray. Format the DVD-RAM.
10
44
No valid HDD card. ≥ Insert a mobile hard disk that has been recorded using a Panasonic SD media storage device. —
Please check write protect tab
on the disc cartridge. ≥ Release protection from the DVD-RAM cartridge or the card. —
Cannot write.
Protected programs are
existed. ≥ The program is write-protected. Cancel the protection. 36
Contents of this disc are pro-
tected. ≥ The disc is write-protected. Cancel Disc Protection. 44
Cannot finish recording com-
pletely. ≥ The program was copy-guarded. —
Cannot record. Disc is full. ≥ No space left on the HDD, disc or card.
‹ Create space by erasing any unwanted programs. [HDD] [RAM]
‹ Use a new disc or card.
36
—
Cannot record. Maximum
amount of programs exceeded.
Cannot record on the disc. ≥ The disc is scratched. Use another disc.
≥ The disc is dirty.
—
62
Please change the disc. ≥ Press [ < ] to remove the disc. (Power goes off.) —
This disc may not be played in
your region. ≥ You tried to play a disc with a region number different from this unit’s region number. This unit
can only play discs with the region numbers compatible with this unit (1, All, or including the
number 1). Cover
page
Your selection exceeds the
recorder’s rating limit. ≥ A ratings level has been set for DVD-Video with this unit. Unlock the unit with “Ratings” in
“Disc”. 51
Finalizing is necessary for
compatible playback. ≥ To enable playback of your DVD-R on compatible equipment, it is necessary to finalize it. 44
/ ≥ Operation is restricted on this unit or disc. —
Cannot playback on this unit. ≥ You tried to play a non-compatible image.
≥ Turn the power off on the main unit and re-insert the card.
11
22
No folder ≥ There is no compatible folder in this unit. 23
PROTECT
LOCK
NO READ ≥ The disc is dirty or badly scratched.
‹ Clean the disc if it is dirty.
‹ The disc cannot be played if it is scratched and this display doesn’t disappear.
≥ The unit cannot read the disc.
≥ You have used a DVD-RAM/PD lens cleaner and it has finished.
62
—
—
—
SELF CHECK ≥ There was a power failure or the AC plug was disconnected while the power was on. The unit is
carrying out its recovery process. Wait until the message disappears. —
UNSUPPORT ≥ You have inserted a disc the unit cannot play or record on. 10
HARD ERR ≥ If the message does not go away after turning the power off and on, consult your dealer for ser-
vice. —
HDD SLEEP ≥ In order to extend HDD life, the HDD is in SLEEP mode. 11
PROG FULL ≥ There are already 32 timer recordings. Erase unnecessary timer recordings. 29
∑ CHK REMOTE
(“ ∑ ” stands for a number.)
≥ The remote control and main unit are using different codes. Change the code on the remote
control. 54
U14 ≥ The unit is hot.
‹ The unit switches to standby automatically for safety reasons and you cannot operate it.
Wait for about 30 minutes for the service number to disappear.
‹ Select a position with good ventilation when installing the unit.
‹ Do not block the cooling fan on the rear of the unit.
—
—
—
U99 ≥ The unit fails to operate properly. Press [ Í , DVD POWER] to switch the unit to standby. Now
press [ Í , DVD POWER] again to turn the unit on.
—