Panasonic BB-HCA10A - Manual (Page 2)

Mounting the Bracket and the Camera
1. Using the included template as a guide, make a hole ( φ 240 mm
[9 7/16 inches]) in the ceiling.
2. Drive an anchor bolt (not included) into the original ceiling and attach a
nut (not included) to the bolt.
• Drive the anchor bolt into the original ceiling directly above the center of
the hole made in step 1.
• The end of the anchor bolt should be 47 mm (1 7/8 inches) above the
bottom of the ceiling board.
• The bottom of the nut should be 61 mm (2 3/8 inches) above the bottom
of the ceiling board.
3. Secure the safety wire to the bracket using screw B (included).
4. Insert the bracket into the hole in the ceiling.
• The camera will face the direction indicated by the arrow on the bracket.
5. Tighten the 3 clamp screws (attached to the bracket) and secure the
bracket.
• The clamps tighten as the screws are tightened.
6. Secure the bracket by attaching and tightening a nut (not included) to the
anchor bolt.
7. Secure the safety wire (included with the camera) to the camera using
screw B (included with the camera) and washer B (included with the
camera).
• Make sure you attach the safety wire when mounting the camera on a
ceiling to prevent the camera from falling.
8. Align the 2 round protrusions on the camera and the holes on the ceiling
plate (included with the camera), tighten the screw to secure the ceiling
plate, then pass the safety wire through the ceiling plate as shown. Make
sure you do not scratch the lens cover when performing this procedure.
9. Attach the connector cover (included) and connect the necessary cables
to the camera.
• Align the “
” of the connector cover with the center of the recessed
area of the bracket.
• Cut spaces in the connector cover to make room for the cables that will
be connected to the camera. Cut along the perforated lines.
10. Attach the camera to the bracket in 3 places using screw B (included).
• Align the arrows on the ceiling plate (included with the camera) and the
bracket when attaching the camera.
11. Secure the ceiling mounting cover (included) to the bracket.
1 Pass the safety wire through the ceiling mounting cover as shown.
2 Align the “ ” marks on the rear of the camera and on the ceiling
mounting cover.
3 Turn the ceiling mounting cover clockwise until the “ ” mark on the rear
of the camera and the “ ” mark on the ceiling mounting cover are
aligned as shown.
• Be careful not to nip the cables, cords, etc.
• To remove the ceiling mounting cover, turn it counterclockwise until the
“ ” mark on the rear of the camera and on the ceiling mounting cover
are aligned, then lower the ceiling mounting cover.
12. Secure the safety wire to the ceiling.
• Secure the bracket’s safety wire first, using screw A and the washer
(included with the bracket), then secure the camera’s safety wire, using
screw A and washer A (both included with the camera).
• Secure the safety wires to the ceiling about 160 mm (6 5/16 inches)
from the center of the camera.
• Do not drive the screws into a soft material. Drive the screws into a
secure, 25 mm (1 inch) thick area of the ceiling, such as a crossbeam,
otherwise the bracket and the camera may fall. If there is no
crossbeam, place a board on the other side of the ceiling to make sure
the bracket and the camera are securely mounted.
Specifications
Template
Anchor bolt
Nut
Ceiling board
Bolt is above center of hole
61 mm (2 3/8 inches) 47 mm
(1 7/8
inches)
Safety wire
Screw B
Clamp screw
Clamp
Ceiling board
Clockwise
Nut
Washer B
(Inside diameter: 2.6 mm [1/8 inches])
Safety wire
Safety wire hole
Screw B
(Length: 10 mm [3/8 inches],
Body diameter: 2.6 mm [1/8 inches])
Operating temperature +0 °C (+32 °F) to +40 °C (+104 °F)
Dimension (W×H×D) About 270 mm (10 5/8 inches) × 77.5 mm
(3 1/16 inches) × 270 mm (10 5/8 inches)
Weight About 900 g (1.98 lb.)
Holes
Screw A (2 pcs.) (Length: 20 mm [13/16 inches],
Body diameter: 4.0 mm [3/16 inches])
Recessed area
Camera direction Ceiling plate arrow
Washer
(Inside diameter:
4.0 mm [3/16 inches])
Screw A
(Length: 20 mm [13/16 inches],
Body diameter: 4.0 mm [3/16 inches])
Washer A
(Inside diameter: 4.0 mm [3/16 inches])
Screw A
(Length: 20 mm [13/16 inches],
Body diameter: 4.0 mm [3/16 inches])
BB-HCA10A_IG.fm Page 2 Tuesday, January 29, 2008 1:59 PM