Panasonic SC-HT680 - Manual (Page 23)

23
RQT7969
This is one of the ways to get appropriate surround effects.
Preparation
Press [DVD/CD].
1
While stopped and no on-screen display is shown
Press [SHIFT] i[TEST] to output a test
signal.
L: Front left C: Center R: Front right
RS: Right surround LS: Left surround
≥There is no output from SW (subwoofer) channel.
2
Press [VOLUME, r] or [s] to set the
volume level normally used for listening.
3
Press [ 3] (increase) or [4] (decrease) to
adjust the speaker level for each speaker.
C, RS, LS: `6 dB to i6 dB
(L, R: Only the balance is adjustable.)
≥To adjust the balance of the front speakers
While outputting the test signal, press [ 2, 1].
≥Adjust the speaker level to the same level as the front
speakers.
To stop the test signal
Press [SHIFT]
i[TEST] again.
∫ To adjust speaker level during play
(Effective when playing multi-channel audio or when Dolby Pro
Logic II or Super Surround is on.)
1
Press [CH SELECT] to select the speaker.
L
#
C
#
R
#
RS
#
LS
#
SW
^-------------------------------------------------}
SW: Subwoofer
≥You can adjust SW only if the disc includes a subwoofer
channel.
≥“SW” does not appear on the display and is not adjustable
when Dolby Pro Logic II is turned on.
≥“S” appears on the display when “MUSIC” or “MOVIE” is
selected with Super Surround ( ➜ page 22). In this case, you
can adjust both surround speaker levels at the same time
using [
3, 4].
S: `6 dB to i6 dB
2
Press [ 3] (increase) or [4] (decrease) to adjust the
speaker level for each speaker.
C, RS, LS, SW: `6 dB to i6 dB
(L, R: Only the balance is adjustable.)
≥To adjust the balance of the front speakers
While “L” or “R” is selected, press [ 2, 1].
Speaker level adjustments SHIFT
TEST
CH SELECT
Other useful functions
Press [SHIFT] i[SLEEP] to select the time (in
minutes).
SLEEP 30 _----)SLEEP 60_----)SLEEP 90
^""""" OFF(_ SLEEP 120(__}
To cancel the timer
Press [SHIFT]
i[SLEEP] to select “OFF”.
To confirm the remaining time
Press [SHIFT]
i[SLEEP] again.
To change the setting
Repeat the procedure from the beginning.
Press [MUTING].
“MUTING” flashes on the unit’s display.
To cancel
≥Press [MUTING] again or reduce the volume to minimum (-- -- dB),
then raise it to the required level.
≥Muting is canceled when you switch the unit to standby.
1
Reduce the volume and connect the
headphones (not included).
Headphone plug type: 3.5 mm ( 1 / 8
z) stereo
2
Adjust headphone volume with
[VOLUME].
≥Audio is automatically switched to stereo (2-channel).
[Note]
Avoid listening for prolonged periods of time to prevent hearing
damage.
Sleep timer
Muting
Using headphones
SHIFT
SLEEP
QUICK OSD
SLEEP
SETUP
MUTING
C
M ain unit only
1 2 3 4 5
OPEN CLOSE DISC CHANGE DISC CHECK SELECTOR
TUNE MODE FM MODE MEMORY
PROGRESSIVE CD MODE DISC
POWER
DOWN UP
PHONES
VOLUME
AC IN
TUNING
VOLUME
S
ound fie
ld
a
nd s
ound qua
lity
/Othe
r us
e
ful func
tions
HT680.book Page 23 Tuesday, December 14, 2004 8:55 AM