Using other functions 10, Reducing the level of an analog signal, Watching video and audio sources independently – Pioneer VSX-82TXS-S User Manual

Page 68: Using the sleep timer, Dimming the display, Switching the speaker impedance

Advertising
background image

Using other functions

10

68

En

• Note that the setting you make here is stored in

memory, even if you switch off the receiver, so if you
want to record a different input source later, you
must do so with

REC SELECT

, or by selecting

RECOUT SOURCE

.

3

After RECOUT disappears from the display, select

the input source you want to listen to.

This will be heard from the main system without affecting

your recording.

1

Tip

• If you have a digital recorder connected to the

DIGITAL OUT1

(

ROOM3

) digital output and

ROOM

3

is switched on (see

Using the multi-room controls

on page 59), you can also select a different input
source for this output while

ROOM 3

shows in the

display.

Reducing the level of an analog signal

The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if you find
the that the

OVER

indicator is lights often, or you can

hear distortion in the sound.

2

Press ANALOG ATT to switch the input attenuator

on or off.

Watching video and audio sources
independently

You can listen to a sound source and select a different
video source on your TV.

While listening to a source, press VIDEO SEL (

VIDEO

SELECT

) to select the video source you want to watch.

Press repeatedly to cycle through the possible video
sources. You can select

DVD

,

TV

,

SAT

,

DVR1

,

DVR2

,

VIDEO1

,

VIDEO2

or

OFF

(no video signal).

3

Using the sleep timer

The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.

Press

SLEEP

repeatedly to set the sleep time.

• You can check the remaining sleep time at any time

by pressing

SLEEP

once. Pressing repeatedly will

cycle through the sleep options again.

4

Dimming the display

You can choose between four brightness levels for the
front panel display. Note that when selecting sources,
the display automatically brightens for a few seconds.

Press DIMMER repeatedly to change the brightness

of the front panel display.

Switching the speaker impedance

We recommend using speakers of 8

with this system,

but it is possible to switch the impedance setting if you
plan to use speakers with a 6

impedance rating.

With the receiver in standby, press

STANDBY/

ON

while holding down the

SPEAKERS

button.

Each time you do this, you switch between the
impedance settings:

SP 6 OHM

– Use this setting if your speakers are

rated at 6

.

SP 8 OHM

– Use this setting if your speakers are

rated at 8

or more.

Note

1 • Note that switching the

ROOM 2

input source (as explained in

Multi-room listening

on page 57) also changes the

RECOUT

input source.

• If

RECOUT SOURCE

is selected, changing the input source likewise changes the input source used for your recording.

2 The attenuator isn’t available with digital sources, or when using the Stream Direct modes.
3 Note that this feature will not work with video sources assigned to either of the HDMI video inputs.

SLEEP

10

SR+

ANALOG
ATT

SC

VIDEO

SEL

DIMMER

S.RETRIEVER

CLASS

D.ACCESS

SLEEP

+10

SR+

ANALOG
ATT

DISC

VIDEO

SEL

DIMMER

S.RETRIEVER

CLASS

D.ACCESS

4 You can also switch off the sleep timer simply by switching off the receiver.

SLEEP

SR+

ANALOG
ATT

VIDEO

SEL

DIMMER

S.RETRIEVER

CLASS

D ACCESS

Off

30 min

60 min

90 min

SLEEP

0

SR+

ANALOG
ATT

VIDEO

SEL

DIMMER

S.RETRIEVER

CLASS

D.ACCESS

VSX_84TXSi.book.fm 68 ページ 2006年3月13日 月曜日 午前11時54分

Advertising
This manual is related to the following products: