Panasonic SV-AP10U User Manual

Page 45

Advertising
background image

Others

45

ª Before, During, and After Printing

≥Do not write on the paper before printing on it.
≥Do not forcibly pull out the Ink Cassette or paper, shake

the printer, or add more paper while printing is in
progress.

≥Removing the Paper Cassette while printing is in

progress could result in a paper jam in which the
jammed paper cannot be pulled out. The jammed paper
can only be removed when the Paper Cassette is
inserted.

≥While printing is in progress, no other buttons besides

the Display/Cancel button used to cancel multiple prints
will work.

≥The printer will make a little noise when printing, but this

is not a malfunction.

≥Printing 2 or more pages, or printing in cold or hot

temperatures may take a little more time.

≥If ink or paper runs out while printing is in progress, it is

unnecessary to press the print button again after you
replace the ink or paper.

≥If you print a dark image with this Photo Printer, it may

become a lighter print by using the AGC (Auto Gain
Control).

≥When paper is bent or wrinkled, it may fall out of the

paper exit tray (located above the Paper Cassette).

Do not allow more than 10 sheets of printed paper to

collect in the paper exit tray, as doing so may lead to
a paper jam.

ª Notes on Using 4" x 6" (100 x 150 mm)

printing paper

≥When printing borderless prints, select [With trim]. A

blank border can be created around the top, bottom, left
and right sides of a picture when selecting [Without
trim].

≥When printing with borderless paper, the top, bottom,

left and right sides of the picture will be cut off.

Cutting Borderless Paper After Printing

1

Fold in both directions along the perforation
lines.

2

Tear along the perforation lines.

≥There are perforation lines on both ends of the

borderless paper. Be sure to tear off both sides.

ª Notes on Handling Finished Prints

In order to preserve finished prints in the best condition,
always observe the following points. Failure to observe
these points could result in a deterioration of print quality
or injury.
≥Do not affix cellophane tape to the printed surface. In

particular, be careful not to let plastic desk pads,
business card cases, or plastic erasers come into
contact with the printed surface.

≥Do not touch the printed surface with your fingers.
≥Do not spill or apply volatile solvents such as alcohol to

the printed surface. Doing so could result in
discolouration or fading.

≥Do not leave printed surfaces in contact with one

another. Doing so could cause color transfer between
the two images. Color transfer could also occur if a
printed surface is left in contact with any other type of
paper under pressure for an extended period of time.

≥Do not store prints under conditions of high

temperatures or high humidity. Leaving prints under
such conditions for an extended period of time could
cause a deterioration in print quality. Do not leave prints
exposed to direct sunlight.

≥When prints are to be stored in an album, select an

album that has nylon pockets. Other materials could
cause color transfer or discolouration. (Polypropylene
and cellophane are also acceptable materials.)

ª Notes on Cards

≥If a card’s image does not display properly, turn off the

power, remove the card, and re-insert it.

≥Some titles recorded to the cards are not displayed on

the Digital Video Camera.

≥This Photo Printer is based on the DCF standards

(Design rule for Camera File system) which were
established by JEITA (Japan Electronics and Information
Technology Industries Association).

≥When the Index Display appears and the image is

based on the DCF standards is selected, the folder/file
number of this image is displayed.

ª Notes on the SD Memory Card Write-

Protect Switch

≥The SD Memory Card has a write-protect switch. Sliding

the switch to [LOCK] prevents the recording of data to
the card as well as the deletion of data from the card.
Sliding back the switch permits such operations.

ª About the Exif Print

This unit corresponds to the image format Exif 2.2 (Exif
Print) that has been established by JEITA.
It is realized that the printed Image is more clear with
recording information added on the image by the Digital
Camera.

1

2

LOCK

AP10U-Eng.book 45 ページ 2002年9月27日 金曜日 午前10時8分

Advertising