Panasonic SC-HT920 - Manual (Page 5)

5
RQT7696
Fr
ont
s
p
ea
ker
a
s
s
e
mb
ly
/Ot
h
er
s
p
ea
ker
s
e
tup
opt
io
ns
4
Connect the speaker cables.
5
Fasten the speaker cable to the base.
≥Using the same polyfoam as in procedure 2 will assist you in
safely and securely fastening the speaker cables.
∫ Preventing the speakers from falling over
Preparation
Attach screw eyes (not included) to secure the speakers to the wall
(‹diagram below)
≥You will need to obtain the appropriate screws to match the walls
and pillars to which the screw eyes are going to be fastened.
≥Consult with a qualified housing contractor concerning the
appropriate procedure when attaching to a concrete wall or a
surface that may not have strong enough support. Improper
attachment may result in damage to the wall or speakers.
1 Thread the string (not included) through the slot on the
rear of the speaker to prevent it from falling over.
2 Loop the string through the screw eye and tie tightly.
Other speaker setup options
∫ Attaching to a wall
1 Drive a screw (not included)
into a wall.
2 Fit the speaker securely onto
the screw(s) with the hole(s).
≥The wall or pillar on which the speakers are to be attached should be
capable of supporting 10 k g (22 lb.) per screw. Consult a qualified
building contractor when attaching the speakers to a wall. Improper
attachment may result in damage to the wall and speakers.
≥When mounting the front speaker to a wall, we recommend using
a string (not included) to prevent it from falling ( ‹ left).
≥Use of optional speaker cables is recommended for wall mounted
front speakers. (You can also remove the speaker cables from the
pipes supplied with this system).
e.g.
Front speaker
Center speaker
∫ Fitting speaker stands
(not included)
Ensure the stands meet these conditions before purchasing them.
Note the diameter and length of the screws and the distance
between screws as shown in the diagram.
≥The stands must be able to support over 10 kg (22 lb.).
≥The stands must be stable even if the speakers are in a high position.
e.g. Surround speaker
Rear of the speaker
_:
Copper
`:
Silver
Push !
If there is any excess
speaker cable, thread the
speaker cable into the
opening near the top of the
pipe while pulling the
speaker cable from the
bottom of the base.
1 Twist off the vinyl ends of the
speaker cables.
2 Press the speaker cable into the groove.
2 Fit the speaker
cable into the
base cover groove
as far as possible.
1 Press the speaker
cable and thread
between the
hooks.
Rear side of base Cable
String (not included)
Wall
Screw eye (not included)
Rear of the speaker
Approx. 150 mm
(5
15 /
16
z)
e.g.
30–35 mm
(1
3 /
16
q–1 3 /
8
q)
‰7.5–9.4 mm
(
19 /
64
q– 3 /
8
q)
8–11 mm
(
3 /
8
q– 7 /
16
q)
230 mm
(9
1 /
16
z)
150 mm
(5
29 /
32
z)
In this position, the
speaker will likely
fall if moved to the
left or right. Move the speaker
so the screw is in
this position.
Speaker stand
(not included)
5 mm ( 13 /
64
z),
pitch 0.8 mm ( 1 /
32
z)
60 mm (2 23 / 64
z)
Plate thickness plus 7 to 10 mm
(plus
9 /
32
z to 25 /
64
z)
Attach the stands to
these metal screw
holes.
Wall or pillar