Setting menus, Recording setup screen – Panasonic AG-DVX100AP User Manual

Page 46

Advertising
background image

46

Item/

(display mode)

Description of settings

1394 UB REGEN
(VCR)

For selecting the user’s bit to be recorded
when recording the signals of the
component connected to the DV connector.
OFF:

The user’s bit selected for the UB MODE
item is used for the recording.

ON:

The user’s bit of the signals input to the
DV connector is used for the recording.

O

When ON has been selected as this item’s
setting, this setting takes precedence over
the UB MODE item setting.

O

The user’s bit is not recorded if the
signals do not contain the user’s bit
information.

O

When no signals are supplied to the DV
connector, the UB MODE item setting is
followed.

RECORDING SETUP screen

Item/

(display mode)

Description of settings

TC MODE
(Camera)
(VCR)

For selecting the time code correction
mode in which the time code of the internal
time code generator is to be recorded.
DF

: The drop frame mode is used.

NDF : The non-drop frame mode is used.

O

When the progressive mode has been
set to 24P or 24P (ADV), the non-drop
frame mode is established regardless of
this item’s setting.

TCG
(Camera)
(VCR)

For setting the operation mode in which the
internal time code generator is to be run.
FREE RUN:

The internal time code generator is run
regardless of the operation mode.

REC RUN:

The internal time code generator is run
during recording.

FIRST REC TC
(Camera)
(VCR)

For selecting the time code which is to be
recorded when recording is started.
REGEN:

Recording proceeds in such a way that
the time code continues on (is
regenerated) from the time code on the
tape.

PRESET:

The time code is not regenerated from
the time code on the tape.
The time code is recorded using the
value set in the TC PRESET item
serving as the initial value.
However, the time code is forcibly
regenerated when shooting with frame-
to-frame continuity has been performed.

TC PRESET
(Camera)
(VCR)

For setting the initial value of the time code
to be recorded.
This item’s setting is valid when PRESET
has been selected as the setting for the
FIRST REC TC item.

O

When the progressive mode has been
set to 24P or 24P (ADV), set the frame
value to 0 or to a multiple of 5. If any
other value is set, the time code
recorded will shift.

1394 TC REGEN
(VCR)

For selecting the time code to be recorded
when recording the signals of a component
connected to the DV connector.
OFF:

The signals are recorded using the time
code which was set using the TC MODE
item, TCG item and FIRST REC TC
item.

ON:

The signals are recorded using the time
code of the signals which have been
input to the DV connector.

O

When ON has been selected as this
item’s setting, this setting takes
precedence over the TC MODE item,
TCG item and FIRST REC TC item
settings.

O

When no signals are supplied to the DV
connector, the TC MODE item, TCG item
and FIRST REC TC item settings are
followed.

Setting menus

The underlining indicates the factory setting.

UB MODE
(Camera)
(VCR)

For setting what is to be recorded as the
user’s bit.
USER:

The user’s information is recorded.

TIME:

The time of the recording is recorded.

DATE:

The date of the recording is recorded.

TCG:

The time code generator’s value is
recorded.

FRM. RATE:

The frame rate information for frame
conversion is recorded.

22

02 22 22

Recording control
information

O

Updated frame information

O

REC START/STOP
information

Frame rate information

O

Frame rate (60, 30 or 24)

O

I/P identification information

O

Conversion information

O

Frame rate coefficient

Frame sequence number

O

A number from 0 to 4 is displayed
in the 24P or 24P (ADV) mode.

O

“F” is displayed in the 60 or 30P
mode.

User’s bit value verification
information

Advertising