Panasonic SC-EN15 - Manual (Page 4)

4
Radio stations can be tuned manually by selecting the station’s frequency or they can be preset into channels to make it easy to tune.
You can preset up to 20 FM channels and up to 12 AM channels.
Each country allocates broadcast bands according to their particular system.
You can change the FM step. The step is factory-set to 0.2 MHz, but you can
change it to receive broadcasts allocated 0.1-MHz steps.
Any FM frequencies preset in channels will be changed by this procedure.
Preset them again.
You can change the AM step. The step is factory-set to 10 kHz, but you can
change it to receive broadcasts allocated 9-kHz steps.
Any AM frequencies preset in channels will be changed by this procedure.
Preset them again.
1. Select the opposite band from the one you are going to change
with [TUNER/BAND].
2. Press and hold [TUNER/BAND] on the unit.
After a few seconds the display changes to show the current minimum
frequency. Continue to hold the button down. The minimum frequency
changes and the step is changed.
To return to the original step, repeat the above steps.
If noise is excessive in FM
You can improve FM reception by switching reception to monaural.
Radio operations
LIGHT
SLEEP
CLOCK/
TIMER ADJ
DISPLAY
TIMER
SET/CHECK
PGM/CLEAR
-AUTO PRESET
OPEN/
CLOSE
1 2 3
4 5 6
7 8
0
9
> = 10
AUX
TUNER/
BAND
CD
EXTRA
D.BASS
SOUND
EQ
LIVE
VIRTUALIZER
PLAY
MODE
ALBUM
VOL VOL
SC-EN15 SC-EN17
PRESET TUNE u ALBUM i
Input using the numbered
buttons
To select a 2-digit number
e.g. 11: [ 10]
→ [1] → [1] >
=
To adjust the volume
TUNER BAND
To adjust the volume
0
(Minimum)
50
(Maximum)
VOLUME
Allocation settings
To improve reception
For U.S.A. and Canada
For units with PX printed on the outer packaging
FM AM
Extend the whip antenna and
adjust its direction. Change the direction and location
of the AM loop antenna.
PLAY MODE
Press to turn the MONO
mode ON/OFF
MONO
Manual
tuning
Select“FM” or “AM”
TUNER/
BAND u i
3 4
Select “FM” or “AM”
Remote control
Main unit
TUNER BAND
Select the frequency
Select the frequency
Automatic
presetting
The tuner
presets all the
stations it can
receive into
channels in
ascending order.
Select “FM” or “AM”
Note
During automatic presetting, the memory indicator
( ) flashes and the frequency scrolls. The
memory indicator and channel numbers are
displayed for a second when a station is preset.
The first station to be preset is displayed when
presetting finishes.
PGM
Manual
presetting
Preset the
stations one at a
time.
PGM/CLEAR
1 2 3
4 5 6
7 8
0
9
> =10
-AUTO PRESET
Select a channel
Tune to
the signal
you want
to set as
the preset.
Note
The station occupying a channel is erased if another
station is preset over that channel.
Selecting
channels
Enter preset mode
PGM
TUNER/
BAND
PGM/CLEAR
-AUTO PRESET
Perform once for FM stations and once for AM stations.
Select a channel
Select a channel
Select “FM” or “AM”
Select “FM” or “AM”
Press and hold until
“AUTO” appears
Within 10 seconds
• Auto tuning stops when it finds a station.
• To cancel auto tuning press the same button again.
Note
• Auto tuning may not function when there is
excessive interference.
Auto
tuning
Select“FM” or “AM”
TUNER/
BAND u i
3 4
Select “FM” or “AM”
Remote control
Main unit
TUNER BAND
Press and hold until the
frequency starts changing
rapidly
Press and hold until the
frequency starts changing
rapidly
TUNER BAND