Panasonic CW-XC122VU - Manual (Page 3)

WINDOW REQUIREMENTS
• Hot sun rays hitting the outside surface
of the cabinet will create considerable
heat load. If the outside of the cabinet is
exposed to direct sunlight, consider
building an awning to shade the cabinet
while providing ample area for the heated
air to be exhausted from the condenser
(both sides) and the top.
This unit is designed for installation in
standard double hung windows.
NOTE
The unit may also be installed “through the wall”. You should,
however, observe standard carpentry practices and frame the
opening without violating local ordinances.
INSTALLATION PROCEDURES
HOW TO ASSEMBLE THE EXPANDABLE PANELS
Top angle
Type B screws
Type C screws
• Attach the top angle to the cabinet using screw type B (3 pcs).
• Insert expandable panels to cabinet sides as shown.
• Secure the first fold of expansion panel to cabinet using screw
type C (3 each).
Expandable panel
CHASSIS INSTALLATION INTO THE CABINET
1 Remove the rear cabinet
screws and save for later use.
2 Slide the chassis out from the
cabinet.
CABINET INSTALLATION
1 Cut the “Sealing Ribbon” to the
proper length, and attach it along
the bottom edge of the bottom
window sash.
2 To prevent condensation water
from dripping inside, the cabinet
should be installed level or very
slightly tilted to the outside.
3 Secure the cabinet using screws.
• Expand the expandable panel fully into the grooves of the
window frame, secure the expandable panel, left, right and
top mounting frames to the bottom of the window sash
using 4 screws type A and 2 screws type B.
• Secure the cabinet using wood screws type A.
• Cut the window sash foam seal to the proper size and
seal the opening between the top of the inside window
sash and the outside window sash.
Note : If a gap exists between the unit and window sash, you may
use “Sealer” supplied with the installation kit for a better seal.
Window sash
sealing ribbon
1 Slide the chassis into the cabinet.
2 Reinstall the cabinet screws.
Secure the cabinet to chassis by using screws (from
rear cabinet).
INSTALLATION OF THE FRONT GRILLE
Depending upon the location
of the AC outlet, route the AC
cord to either the left or right
side while installing the front
grille.
OFF/ON OPERATIO N TEMP/TIMER
COOL
FAN
HIGH
MED
LOW MODE
FAN SPEE D
SET TIMER
SET/ CANCEL AIR SWIN G ECONOMY
hr ° F
Wireless
R emote C o ntrol
This figure shows the AC cord
routed to the left side.
INSERT THE AIR FILTER
Attach the air filter to the intake grille
PLACE FRONT INTAKE GRILLE OVER THE FRONT GRILLE
Slide the front intake grille slightly to the right to reattach the
tabs and then push it down to close tight.
Lift up about 90°.
NOTE
This procedure applies to left and right
of assembling expandable panel.
OFF/ON OPERA TION TEMP/TIMER
COOL
FAN
HIGH
MED
LOW MODE
FAN SPEED
SET TIMER
SET/ CANCEL AIR SWING ECONOMY
hr ° F
Wireless
R emote C o ntrol
OFF/ON
OPERATION TEMP/TIMER
COOL FAN HIGH MED LOW
MODE
FAN SPEED
SET TIMER
SET/ CANCEL
AIR SWING ECONOMY
hr ° F
Wireless R emote C o ntrol
OFF/ON OPERATIO N TEMP/TIM ER
COOL
FAN
HIGH
MED
LOW MODE
FAN SPEE D
SET TIMER SET/ CANCEL
AIR SWIN G ECONOMY
hr ° F
Wireless
R emote C o ntrol
OFF/ON OPERATIO N TEMP/TIMER
COOL
FAN
HIGH
MED
LOW MODE
FAN SPEE D
SET TIMER
SET/ CANCEL AIR SWIN G ECONOMY
hr ° F
Wireless
R emote C o ntrol
OFF/ON OPERATIO N TEMP/TIME R COOL
FAN
HIGH
MED
LOW MODE FAN SPEE D
SET TIMER SET/ CANCEL AIR SWIN G ECONOMY
hr ° F
Wireless
R emote C o ntrol
1 Place the front grille on the
cabinet first.
2 Secure the front grille to the
main chassis using screw
provided.
15-
15
/ 16
”
(min)
22 to 42- 1 / 8 ”
Top sealing
ribbon (To be
attached to the
top angle)
Side sealing ribbon
(To be attached to
the expandable
panel)
Window sash
foam seal
Type A
screw
Type B
screws
Window sill
Type A
screws
Expandable panel
Outside of sash
Window sash
Sealing ribbon
Top angle
Inside of
sash